IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Nylon Monofilament by Melt Spinning
Fishing line and strimmer line are single strands of nylon. Molten nylon is extruded through tiny holes, a spinneret, into strands, which are cooled, stretched to line up the polymer chains and give strength, and wound on spools. Hole size and stretching set the line's thickness and breaking strength. It is the 3D-printer filament line made much finer, and drawn.
Ilọsíwájú
Continuous (industrial)
Ìlànà
1
1
Dry and melt
Dry and melt
Nylon pellets are dried and melted along the extruder's screw.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Àwọn kóró nylon50 kgÀwọn irinṣẹ́ tí a nílò:
Ẹ̀rọ ìgbẹ kóró
Ẹ̀rọ ìtújáde ṣíṣu
Àpò ìfúnni pellet2
2
Spin
Spin
The melt is metered through a spinneret, each hole making one strand.
Àwọn irinṣẹ́ tí a nílò:
Àwo ìranfọ́nrán3
3
Quench and draw
Quench and draw
Strands are cooled in water, then stretched between rolls running at increasing speeds.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Omi200 lítà4
4
Wind and test
Wind and test
The line is wound on spools; its diameter and breaking strength are measured.
Àwọn irinṣẹ́ tí a nílò:
Òṣùwọ̀n Kálípà Díjítà Ìnṣì 6Àwọn irinṣẹ́ tó nílò
5Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.