IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
S-Dasher Friction-Board Churn: A Double-Curved Dasher Throwing Cream Over Grooved Boards
The Walkers lined a square churn with grooved boards so the cream would be thrown against them "thus keeping up a constant friction on all sides."
William Walker and Matthew C. Walker of Lancaster, Pennsylvania, received US 7,554, dated 6 August 1850, for a square water-tight box about fourteen inches each way holding about 40 quarts, half filled, with a "double curved or S shaped dasher" revolving in the centre by a crank and a thumb screw. Four grooved cross pieces run along each side of its curved ends; a friction board grooved underneath inclines across the top; a triangular board returns the cream onto it; a grooved friction piece sits in the lower right corner.
This rung checks the box's capacity, then prints the S dasher, friction boards and corner piece, fits them in a box, and makes butter.
Àárín
About 4 hours, plus printing
Ìlànà
1
1
Capacity
Capacity
Ń ṣí ìwé Jupyter…
2
2
A shaped dash in a box churn before it
A shaped dash in a box churn before it
The embedded blueprint twists its wings into a screw. The Walkers bend theirs into an S and add grooved boards round the box for friction.
3
3
Read US 7,554
Read US 7,554
"As the churn is put in operation, the cream is thrown against the grooves of the incline board E, dashed around and under it, and passed over and against the friction piece G, in the right hand corner of box, while the ends of the dasher H and wide cross piece N keep the cream continually dashing against the grooves of the incline board E thus keeping up a constant friction on all sides."
4
4
Print the parts
Print the parts
Print the S dasher with its four grooved cross pieces in one piece (/uploads/blueprints/s-dasher-friction-board-churn-s-dasher.stl), the grooved incline board (/uploads/blueprints/s-dasher-friction-board-churn-incline-board.stl), the grooved corner piece (/uploads/blueprints/s-dasher-friction-board-churn-corner-piece.stl) and the crank arm (/uploads/blueprints/s-dasher-friction-board-churn-crank-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Okùn PETG1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ẹ̀rọ ìtẹ̀ 3D oníwàyà (FDM)5
5
Fit the box
Fit the box
Take a food-safe box about 180 mm each way. Glue the incline board across the top, sloping down to within 20 mm of the left side, grooves underneath, and a triangular plywood board on that side to turn the cream back onto it. Glue the corner piece in the lower right corner. Drill both ends on the centre for the dasher's shaft.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Àgọ́ ìtọ́jú ti ìpele oúnjẹ1 ẹyọ
Àwo igi tí a lẹ̀ pọ̀1 ẹyọ
Ìdílẹ̀ Silikoni1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ayùn Kópìngì
Ẹ̀rọ Ìlùkòkò Aláìlókùn
Àkójọ Orí Ìlùkòkò
Àwọn clamp6
6
Dasher and crank
Dasher and crank
Pass a 10 mm square hardwood shaft through the box and the dasher, glue the crank arm and a dowel handle on one end, and hold the other with a thumb screw through a washer, as theirs. Cut an air hole in the lid.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Àwọn dowel igi líle1 ẹyọ
Skurú ẹ̀rọ1 ẹyọ
Wáṣà Pẹrẹsẹ1 ẹyọ
Ìdìpọ̀ Igi1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ayùn Ọwọ́Ẹ̀rọ Ìlùkòkò Aláìlókùn
Ìṣù àwọn ohun ìyí skurú7
7
The patent drawing
The patent drawing
US 7,554 drawing sheet, public domain (expired patent).
8
8
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Fill the box half full, about 2.9 litres. Crank steadily; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ọ̀rá wàrà tó nípọn2900 ml
Iyọ̀ Òkun Rúkèrúdò1 ẹyọ
Omi1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ẹ̀rọ ìwọ̀n ooru oníhun tí ó dúró sí inú
Aago Ìdúró
Òṣùwọ̀n Díjítà Ilé Ìdáná
Àwo ìdàpọ̀ ńlá ti irin tí kò ń yá9
9
Dasher that strikes, cream that escapes
Dasher that strikes, cream that escapes
S-dasher friction-board troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**William Walker and Matthew C. Walker** of Lancaster, Pennsylvania, received US 7,554, dated 6 August 1850. Their box was of inch boards; a ledge at the top confined the lid, with a projecting strip on its underside to close it tight, and an aperture M let the air through. They claimed the double-curved S-shaped dasher with the grooved pieces.
**Honest limits.** A food-safe box and printed parts stand in for their wooden churn, at about a third of its size. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Àwọn ohun-èlò
11- 1 ẹyọÀyè
- Àyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 2900 mlÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
Àwọn irinṣẹ́ tó nílò
11- Àyè
- 1 vendor sell this, none ship to you yetÀyè
- Àyè
- Àyè
- Àyè
Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
Quarter-Twist Spiral Dash Churn: Wings Twisted Between Arms Set at Right Angles
láti ọwọ́ Woody
Iṣẹ́ Igi
12
0
0
0
0
0
Butter-Strainer Churn: Cream Thrown Into a Strainer That Keeps the Butter
láti ọwọ́ TheChef
OÚNJẸ ÀTI OHUN MÍMU
28
0
0
0
0
0
Shaftless Dasher-Wheel Churn: Bevelled Buckets Drive the Cream to the Centre
láti ọwọ́ Martin
OÚNJẸ ÀTI OHUN MÍMU
26
0
0
0
0
0
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.