IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Stick Shuttle Cut from a Beech Strip
The shuttle carries the weft yarn through the shed of the loom. The simplest is the stick shuttle: a flat, narrow piece of hard wood with notches at the ends to hold the wound weft. Saw a thin beech strip a little longer than the cloth is wide, cut forked notches at both ends, round every edge and polish it smooth so it slides.
The picture: two stick shuttles wound with yarn.
Olùbẹ̀rẹ̀
An afternoon
Ìlànà
1
1
Cut the strip
Cut the strip
Saw and plane a straight-grained beech strip about 6 mm thick and 4 cm wide, a little longer than the cloth is wide (step 5).
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Igi beech1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ayùn Ọwọ́
Ohun èlò ìfárí igi (pìlánì)
Ìdíwọ̀n2
2
Cut the notches
Cut the notches
Drill a hole near each end and saw from the end into it, making a forked notch that holds the yarn. Cut a shallow long slot in the middle if you like, to make the shuttle lighter.
Àwọn irinṣẹ́ tí a nílò:
Ìlù ọwọ́
Ayùn Kópìngì3
3
Round and smooth
Round and smooth
Round all the edges and points with the knife and rasp so nothing can catch the warp, then sand it smooth.
Àwọn irinṣẹ́ tí a nílò:
Ọ̀bẹ Sìlóìdì
Rásípù igi
Bébà Ìfá4
4
Wax it
Wax it
Rub in beeswax and polish so the shuttle slides through the shed.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ìdí Oyin0.01 kgÀwọn irinṣẹ́ tí a nílò:
Bébà Ìfá5
5
Shuttle length for the cloth
Shuttle length for the cloth
Ń ṣí ìwé Jupyter…
Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.