IṢẸ́ ỌNÀ
ẸWÀ ÀTI ÌLERA
IṢẸ́ ỌWỌ́
ÀṢÀ ÀTI ÌTÀN
ÌṢERÉ
ÀYÍKÁ
OÚNJẸ ÀTI OHUN MÍMU
REVERSE ENGINEERING
SÁYẸ́ǸSÌ
ERÉ ÌDÁRAYÁ
ÌMỌ̀-Ẹ̀RỌ
ÀWỌN OHUN WÍWỌ̀
Toothed-Disk Potato Masher: Teeth Split It, Holes Take It
A perforated masher only pushes; firm pieces roll away from the holes.
George A. Anderson and Charles J. Baker of Albany, New York, received US 108,083, dated 11 October 1870, for a utensil for preparing potatoes and meat: a metal disk with several series of incising teeth and perforations placed alternate, the teeth's width radial; pressed down, "the incisors ... will enter the vegetables and split them at each point in contact, when the broken portions of the vegetables operated upon will rise up and pass through the openings."
This rung works out the teeth and open area, then prints the disk, fits a handle, and mashes potatoes.
Olùbẹ̀rẹ̀
About 1 hour, plus printing
Ìlànà
1
1
Teeth and open area
Teeth and open area
Ń ṣí ìwé Jupyter…
2
2
A perforated disk before it
A perforated disk before it
The embedded blueprint mashes through a perforated disk. Anderson and Baker put teeth between the holes to split the potato first.
3
3
Read US 108,083
Read US 108,083
"We prefer to have the said incisors c to have their width run in the direction of the radii of a circle, as shown in fig. 1, which would strengthen the rim, inclosing the outer series of perforations a with the rim inclosing the inner series of perforations a, and permit the metal of the disk A being made lighter."
4
4
Print the disk
Print the disk
Print the disk with its teeth and socket (/uploads/blueprints/toothed-disk-potato-masher-disk.stl) socket down, teeth up. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Okùn PETG1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ẹ̀rọ ìtẹ̀ 3D oníwàyà (FDM)5
5
Fit the handle
Fit the handle
Epoxy a 16 mm hardwood dowel 170 mm long into the socket.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Àwọn dowel igi líle1 ẹyọ
Ẹpọ́ksì Ẹ̀yà Méjì1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ayùn Irin
Òṣùwọ̀n Kálípà Díjítà Ìnṣì 66
6
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: an 84 mm disk with 8 inner and 14 outer radial incisors alternating with as many round holes, its socket and handle.
7
7
Mash firm potatoes
Mash firm potatoes
Boil 500 g of potatoes in their skins for about 25 minutes until a knife slides in; drain. Mash half with the toothed disk and time it to no lumps; compare with the yielding-disk masher if you built it.
Àwọn ohun èlò fún ìgbésẹ̀ yìí:
Ọ̀dùnkún1 ẹyọ
Omi1 ẹyọÀwọn irinṣẹ́ tí a nílò:
Ìkòkò olódi gíga
Àwo ìdàpọ̀ ńlá ti irin tí kò ń yá
Aago Ìdúró8
8
Teeth that bend, holes that clog
Teeth that bend, holes that clog
Toothed-disk potato masher troubleshooting.
Flow
Loading...
9
9
History and honest limits
History and honest limits
**George A. Anderson** and **Charles J. Baker** of Albany, New York, received US 108,083, dated 11 October 1870. Two opposite sides of each perforation depend below the disk as the incisors; any suitable handle may be fixed by a socket, upright or at an angle. They named meat as well as potatoes.
**Honest limits.** A printed disk stands in for their metal one. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times are the result.
Àwọn ohun-èlò
5- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
- 1 ẹyọÀyè
Àwọn irinṣẹ́ tó nílò
6- Àyè
- Àyè
Àwọn fáìlì àpẹrẹ
1Ìtọ́nisọ́nà yìí ń ṣe
Blueprint tó jọra
Àwọn blueprint wọ̀nyí pín ìmọ̀ — ọ̀nà, ohun-èlò tàbí ìlànà
Yielding-Disk Potato Masher: A Perforated Disk That Rocks to the Mash
láti ọwọ́ TheChef
OÚNJẸ ÀTI OHUN MÍMU
34
0
0
0
0
0
Wire-Coil Potato Masher: A Flat Spiral of Wire on Five Braces
láti ọwọ́ Forge
Iṣẹ́ Irin
21
0
0
0
0
0
Draining-Tube Potato Masher: Mash in a Tube, the Water Runs Out
láti ọwọ́ YourGrandma
OÚNJẸ ÀTI OHUN MÍMU
21
0
0
0
0
0
CC0 Àgbègbè Gbogbogbò
Blueprint yìí ti jáde lábẹ́ CC0. O lè ṣe àdàkọ, yí padà, pín, àti lò láìsí ìyọ̀ǹda.
Ṣàtìlẹ́yìn Olùṣẹ́dá nípa rírà àwọn ọjà nipasẹ̀ Blueprint wọn Ẹ̀san Olùṣẹ́dá tí àwọn Olùtajà gbé kalẹ̀, tàbí ṣẹ̀dá àtúnṣe tuntun ti Blueprint yìí kí o sì fi sínú Blueprint rẹ gẹ́gẹ́ bí ìsopọ̀ láti pín owó-wíwọlé.