सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Adjustable Bench Power Supply: Constant Voltage / Constant Current with Cross-Over Lamps (Gately, Forbro, US 3,303,411, 1967)
Ed

सिर्जनाकर्ता

Ed

3. नोभेम्बर 2026FI
४
०
०
०
०

Adjustable Bench Power Supply: Constant Voltage / Constant Current with Cross-Over Lamps (Gately, Forbro, US 3,303,411, 1967)

An all-transistor bench supply with two knobs: one sets the voltage, the other the current. It holds the set voltage until the load tries to draw more than the set current, then switches at once to holding the current, and back again, with no in-between state. Two lamps show which mode is in control. Result: an adjustable constant-voltage / constant-current DC supply with mode lamps. Source: J. R. Gately (Forbro Design), US 3,303,411 (1967). Unknown: all component values and ratings. Builds on the same inventor's 1966 current-limited supply. Picture: the patent drawing.
उन्नत
Unknown

निर्देशनहरू

1

Build the raw supplies

In a case, wire the cord through a switch and fuse to two power transformers, each with rectifiers and a filter: one gives the main power to be regulated, the other the bias supplies, held steady by Zener diodes. Not given: the voltages. Ours: the case, switch and fuse.

यस चरणका सामग्री:

एलुमिनियमको बाकसएलुमिनियमको बाकस1 टुक्रा
प्लग भएको लचिलो तारप्लग भएको लचिलो तार1 टुक्रा
टगल स्विचटगल स्विच1 टुक्रा
फ्युजफ्युज1 टुक्रा
स्टेप-डाउन ट्रान्सफर्मरस्टेप-डाउन ट्रान्सफर्मर2 टुक्रा
डायोडडायोड6 rectifiers
इलेक्ट्रोलाइटिक क्यापासिटरइलेक्ट्रोलाइटिक क्यापासिटर3 filters
जेनर डायोडजेनर डायोड2 bias

चाहिने औजार:

हाते ड्रिलहाते ड्रिल
स्क्रुड्राइभर सेटस्क्रुड्राइभर सेट
2

Fit the pass transistor and current bridge

Put a power transistor on a heat sink in series with the output: collector to the negative supply, emitter through a current-sensing resistor to the negative output terminal. Make the current bridge from the sensing resistor, a reference Zener, a reference resistor and the adjustable current-control resistor: the output current is proportional to its setting. A small trimming resistor sets the maximum current. Not given: the values.

यस चरणका सामग्री:

पावर ट्रान्जिस्टरपावर ट्रान्जिस्टर1 series pass
हिट सिंकहिट सिंक1 टुक्रा
जेनर डायोडजेनर डायोड1 current reference
रियोस्टेटरियोस्टेट1 current control
प्रतिरोधप्रतिरोध1 sensing, reference, trim set
बाइन्डिङ पोस्टबाइन्डिङ पोस्ट2 output + and -

चाहिने औजार:

टाँका लगाउने डन्डीटाँका लगाउने डन्डी
3

Build the voltage bridge

Make the voltage bridge from a reference Zener, a reference resistor, the adjustable voltage-control resistor and the load itself across the output. A small trimming resistor sets the maximum voltage. Add two resistors that feed the current bridge enough extra to cover the voltage bridge's own current and any voltmeter across the output, so low currents are still held exactly.

यस चरणका सामग्री:

जेनर डायोडजेनर डायोड1 voltage reference
रियोस्टेटरियोस्टेट1 voltage control
प्रतिरोधप्रतिरोध1 reference, trim, compensation set

चाहिने औजार:

टाँका लगाउने डन्डीटाँका लगाउने डन्डी
4

Build the amplifiers and cross-over

Give each bridge an error amplifier. Feed the two amplified errors to the bases of a pair of transistors sharing one emitter resistor: whichever base is the more negative takes control and cuts the other off, so the supply is always cleanly in voltage mode or current mode. Amplify the shared emitter signal through two more transistors to drive the pass transistor's base. Add an emitter-follower clamp on the bias line. Not given: the transistor types.

यस चरणका सामग्री:

मुद्रित सर्किट बोर्डमुद्रित सर्किट बोर्ड1 टुक्रा
ट्रान्जिस्टरको विविध सेटट्रान्जिस्टरको विविध सेट1 error amplifiers, cross-over pair, drivers, clamp
प्रतिरोधप्रतिरोध1 सेट
पोटेन्सियोमिटरपोटेन्सियोमिटर1 clamp divider
सोल्डर तारसोल्डर तार1 as needed

चाहिने औजार:

टाँका लगाउने डन्डीटाँका लगाउने डन्डी
5

Fit the mode lamps and use it

From the cross-over pair, drive two lamp transistors, each lighting one lamp: one for voltage mode, one for current mode. In use, set the voltage and the current limit. With a light load the voltage lamp is lit and the voltage holds; if the load tries to draw more than the set current, the supply switches to holding the current and the current lamp lights.

यस चरणका सामग्री:

ट्रान्जिस्टरको विविध सेटट्रान्जिस्टरको विविध सेट1 two lamp drivers
बल्ब होल्डरबल्ब होल्डर2 टुक्रा
बल्बबल्ब2 टुक्रा

चाहिने औजार:

स्क्रुड्राइभर सेटस्क्रुड्राइभर सेट

सामग्री

19

आवश्यक उपकरणहरू

3

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...