सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)
Woody

सिर्जनाकर्ता

Woody

4. नोभेम्बर 2026NO
१२
०
०
०
०

Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)

A shop belt sander for dressing wood surfaces: a 6 in garnet-paper belt running over four crowned wooden pulleys, one driven by the lathe, pressed down onto the work with a hand float. Best belt speed about 2,500 ft per minute; leave about 1 in between work and belt. Source: Popular Mechanics Shop Notes for 1919, p. 3235. Picture: the article's drawing.
मध्यम
Unknown

निर्देशनहरू

1

Turn the pulleys

Build up four solid wood pulleys 10 in across with 8 in faces and turn them in the lathe with a very slight crown; too much crown harms the belt.

यस चरणका सामग्री:

कडा काठको फल्याककडा काठको फल्याक4 built-up pulleys

चाहिने औजार:

काठको खरादकाठको खराद
2

Mount the pulleys

Mount one pulley on a firmly held arbor in the lathe and the other three on iron-pipe shafts on a frame (drawing). Turn and file a true journal on each pipe, pour babbitt bushings in the pulleys, and cut oil grooves in the pipe or babbitt. Supporting the shafts on one side lets the belt slip off; supporting both sides is stronger.

यस चरणका सामग्री:

इस्पात पाइप (बाक्लो भित्ता, चुर्केदार छेउ)इस्पात पाइप (बाक्लो भित्ता, चुर्केदार छेउ)3 shafts
अज्ञात धातुअज्ञात धातु1 babbitt bushings
सल्लाको काठसल्लाको काठ1 frame

चाहिने औजार:

धातुको रेतीधातुको रेती
प्वाल भएको पन्युप्वाल भएको पन्यु
हाते आराहाते आरा
घनघन
3

Make the belt

Cut 6 in garnet paper (No. 1 1/2 for general work) so the ends just meet over the pulleys. Glue the smooth side at the joint, splice it with a strip of cloth about 1 in wide and then one about 3 in wide, cover each side with paper, and clamp between two small boards.

यस चरणका सामग्री:

गिट्टी कागजगिट्टी कागज1 6 in garnet paper
सुतीको कपडासुतीको कपडा1 टुक्रा
पशु सरेसपशु सरेस1 टुक्रा

चाहिने औजार:

सी-आकारको क्ल्याम्पसी-आकारको क्ल्याम्प
4

Set up and run

Run the belt at about 2,500 ft per minute using the lathe's cone pulley. Set the work about 1 in below the belt on a table or a low sliding platform (two sets of tongue-and-groove joints at right angles), start the machine and press the belt down with a float like a blackboard eraser, or a roller.

यस चरणका सामग्री:

सल्लाको काठसल्लाको काठ1 platform, float

चाहिने औजार:

काठको खरादकाठको खराद

सामग्री

7

आवश्यक उपकरणहरू

6

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...