सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Ski Staff: Bamboo Pole With Wrist Loop, Wooden Snow Disk and Lead-Set Spike (Boy Mechanic, 1915)
Woody

सिर्जनाकर्ता

Woody

13. नोभेम्बर 2026NO
९
०
०
०
०

Ski Staff: Bamboo Pole With Wrist Loop, Wooden Snow Disk and Lead-Set Spike (Boy Mechanic, 1915)

A homemade ski staff from The Boy Mechanic, Book 2 (1915): a 4-1/2 ft bamboo pole with a leather wrist loop at the top, a 5 in pine disk 6 in above the tip to stop it sinking in deep snow, and a wire spike set in lead in a hardwood plug for icy ground.
शुरुआती
About 3 hours

निर्देशनहरू

1

His sizes in centimetres

Jupyter नोटबुक लोड हुँदैछ…
2

Read The Boy Mechanic, Book 2

"A ski staff will greatly assist progress over level stretches and is an aid to the ski runner in preserving his balance."
3

Cut the staff and loop

Cut a bamboo pole 1-1/4 or 1-1/2 in in diameter and 4-1/2 ft long. Shave an old strap thinner, cut it about 1/2 in wide, and fix it as a narrow wrist loop at the top.

यस चरणका सामग्री:

बाँसका लिँडेबाँसका लिँडे1 टुक्रा
हार्नेसको छालाहार्नेसको छाला1 टुक्रा
तामाका रिभेटतामाका रिभेट1 टुक्रा

चाहिने औजार:

हाते आराहाते आरा
छाला काट्ने छुरीछाला काट्ने छुरी
हाते ड्रिलहाते ड्रिल
घनघन
नाप्ने फित्तानाप्ने फित्ता
4

Make and fix the snow disk

Cut a disk of well-seasoned white pine or spruce, 1/2 in thick and 5 in in diameter, and coat it with shellac. Bore its centre to pass up the staff about 6 in. Fix it with two pieces of heavy wire: wire A goes through the staff below wire B and at right angles to it, so B must be bent over A. Staple both wires to the disk.

यस चरणका सामग्री:

सल्लाको फल्याकसल्लाको फल्याक1 टुक्रा
सेलाकको वार्निससेलाकको वार्निस1 टुक्रा
फलामे तारफलामे तार1 टुक्रा
तारको स्टेपलतारको स्टेपल4 टुक्रा

चाहिने औजार:

वक्र काट्ने आरावक्र काट्ने आरा
हातले घुमाउने ड्रिल र बिटहातले घुमाउने ड्रिल र बिट
हाते ड्रिलहाते ड्रिल
चेप्टो मुखको प्लासचेप्टो मुखको प्लास
घनघन
चौडा रङ्गाउने बुरुसचौडा रङ्गाउने बुरुस
5

Set the spike

Plug the lower end with hard wood and bore part way into its centre for a wire spike. Cut slight recesses in the sides of the hole to anchor lead, and pour melted lead round the spike. Sharpen the point, then wind the bamboo with waxed twine or fine wire so it does not split.

यस चरणका सामग्री:

कडा काठको फल्याककडा काठको फल्याक1 टुक्रा
फलामे तारफलामे तार1 टुक्रा
सिसाको सिल्लीसिसाको सिल्ली1 टुक्रा
जुटको डोरीजुटको डोरी1 टुक्रा
मौरीको मैनमौरीको मैन1 टुक्रा

चाहिने औजार:

हाते ड्रिलहाते ड्रिल
छिनाहरूछिनाहरू
धातुको डाडुधातुको डाडु
प्रोपेन टर्चप्रोपेन टर्च
रेती (हातको रेती)रेती (हातको रेती)
चेप्टो मुखको प्लासचेप्टो मुखको प्लास
6

Troubleshooting

Ski staff troubleshooting.

Flow

Loading...
7

History and honest limits

From "How to Make a Ski Staff", in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 51). No contributor is named. He gives no wire gauge or spike length. The tools and metric figures are ours.

सामग्री

11

आवश्यक उपकरणहरू

13

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...