सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Flat-Bit Tongs and the Tongs Made from Them, down to Crucible Tongs: Welded Reins, Riveted Joint (Edwinson, 1886)
Forge

सिर्जनाकर्ता

Forge

14. नोभेम्बर 2026NO
१०
०
०
०
०

Flat-Bit Tongs and the Tongs Made from Them, down to Crucible Tongs: Welded Reins, Riveted Joint (Edwinson, 1886)

George Edwinson's tong-making lesson from Amateur Work (1886): jaws forged from inch-square iron, reins of 5/8 in. rod scarfed and welded on, the halves riveted with a hot iron pin. The same flat-bit tongs are then reshaped into pincer, hammer and crook-bit tongs, light smith's pliers, and thinned and curved into crucible tongs.
उन्नत
A day at the forge

निर्देशनहरू

1

His sizes

Jupyter नोटबुक लोड हुँदैछ…
2

Read Edwinson

"Indeed, the man who can turn out a good pair of tongs may be trusted with almost any job in the smithy."
3

Forge the reins

Cut two pieces of 5/8 in. (16 mm) iron rod, each 2 ft (0.6 m) long, with a cold chisel. Bring one end of each to a white welding heat and draw 3-4 in. down to a taper from 5/8 to 1/2 in., rounded for the hand. Upset the other ends at a white heat and scarf them (his figs. 27-28).

यस चरणका सामग्री:

पिटेको फलामको डण्डीपिटेको फलामको डण्डी1 टुक्रा

चाहिने औजार:

चिसो छिनोचिसो छिनो
आरनको भट्टीआरनको भट्टी
निहुँनिहुँ
घनघन
आरनको सँड़सीआरनको सँड़सी
4

Forge the jaws

Cut two 6 in. pieces of 1 in. square iron (or one 12 in. bar, worked from each end before cutting, fig. 29). Forge each jaw end 4 in. long, 1 1/4 in. wide and 3/8 in. thick. Flatten the other end to 1/4 in. thick, round it for the joint (fig. 30) and draw it to a slightly rounded taper (fig. 31).

यस चरणका सामग्री:

नरम इस्पातको चौकुने डन्डानरम इस्पातको चौकुने डन्डा1 टुक्रा

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
निहुँनिहुँ
घनघन
आरनको सँड़सीआरनको सँड़सी
5

Punch the joint

Mark the hole with a centre punch, heat, and punch a 3/8 in. hole over the anvil's heel hole with an iron punch tapering 1/4 to 1/2 in. (fig. 35), or a steel punch of 5/8 in. tool steel.

यस चरणका सामग्री:

औजार इस्पातको डन्डीऔजार इस्पातको डन्डी1 टुक्रा

चाहिने औजार:

केन्द्र ठोक्ने कीलाकेन्द्र ठोक्ने कीला
आरनको भट्टीआरनको भट्टी
निहुँनिहुँ
घनघन
6

Weld jaw to rein

Scarf the taper end of each jaw to fit a rein. Heat both to a welding heat in a clear fire, throw on clean fine fresh-water sand and heat until pasty. Tap the scarfs together lightly, return to the fire a moment, and finish the weld. At a red heat forge the square part to blend into the round rein (fig. 32).

यस चरणका सामग्री:

बालुवाबालुवा1 टुक्रा

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
निहुँनिहुँ
घनघन
आरनको सँड़सीआरनको सँड़सी
7

Rivet the joint

Smiths' way: nick a 3/8 in. round iron rod to rivet length, put the halves together, insert the hot end, twist it off, let 1/4 in. stand below, and rivet both sides. (Or make a 3/4 x 3/8 in. button-headed rivet in a 3/8 in. hole in a flat iron.) If the joint locks, reheat jaws and pin to bright red and work them free.

यस चरणका सामग्री:

पिटेको फलामको डण्डीपिटेको फलामको डण्डी1 टुक्रा

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
निहुँनिहुँ
घनघन
काँटीको टाउको बनाउने पाताकाँटीको टाउको बनाउने पाता
8

Set the jaws

Heat the jaws and set them to the width of the stock to be held. Spring them wider with a piece of cold iron between and a few light blows.

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
निहुँनिहुँ
घनघन
9

Crucible tongs and other forms

From flat-bit tongs at the fig. 32 stage: lengthen and curve the bits for pincer tongs (angular notches hold round or square bars), more for hammer tongs, bend them sideways for crook-bit tongs. Small flat-bit tongs with lengthened, shaped bits are smith's pliers; thin those out further and curve them like pincers to make crucible tongs for hot crucibles and pots of molten metal. Heavy tongs 2-5 ft long need stouter iron.

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
निहुँनिहुँ
घनघन
आरनको सँड़सीआरनको सँड़सी
10

Troubleshooting

Tongs troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" III, **Amateur Work, Illustrated**, vol. V (1886), pp. 266-269 (checked on the archive.org scan amateurworkillus05lond). He gives full sizes only for the flat-bit tongs; crucible tong sizes and curvature are left to the work. Metric figures and tools are ours.

सामग्री

4

आवश्यक उपकरणहरू

7

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...