कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Forged Hunting Axe (Hatchet)
Forge

सिर्जनाकर्ता

Forge

11. अक्टोबर 2026NO
३२
०
०
०
०

Forged Hunting Axe (Hatchet)

A small one-handed axe forged from a 7/8 × 2-inch bar of good tool steel, best made by two people; a 6¾-inch bar gives two heads. The eye, about 9/16 × 1½ inches, is punched at a yellow heat with an eye punch and opened with drifts, the blade drawn out to a 3-inch edge and the head cut to length. The axe is annealed in lime or ashes, ground and buffed, then hardened from the hardening heat in tepid water and tempered by two hot iron bars laid on either side at the centre: dark purple for the blade, blue for the head.
उन्नत
4–6 hours

निर्देशनहरू

1

Mark and punch the eye

Mark the stock with chisel and centre punch. At a yellow heat, punch the eye with the narrow edge of the punch toward the blade; lift the punch after each blow to check it runs straight and to let it cool; a little fine coal in the hole stops it sticking. Punch nearly through, then finish from the other side.

यस चरणका सामग्री:

चेप्टो टुल स्टिलको डन्डीचेप्टो टुल स्टिलको डन्डी1 टुक्रा

चाहिने औजार:

केन्द्र ठोक्ने कीलाकेन्द्र ठोक्ने कीला
आरनको भट्टीआरनको भट्टी
निहुँनिहुँ
तातो प्वाल पार्नेतातो प्वाल पार्ने
घनघन
आरनको सँड़सीआरनको सँड़सी
2

Drift and draw out

Drive in a tool-steel drift, hammer the bulges down to the bar's size and smooth with a flatter; take the drift out before each reheat. Use two drifts, the first 3/8 inch narrower. Draw out the blade, driving the drift back in as the eye stretches so no cold shut forms.

चाहिने औजार:

प्वाल ठूलो पार्ने टेपरप्वाल ठूलो पार्ने टेपर
सम्म पार्ने औजारसम्म पार्ने औजार
उचालेर खसाल्ने घनउचालेर खसाल्ने घन
3

Shape and trim

Shape the blade with a heavy hammer and flatter and form its edge. Cut the head from the bar, draw it to size, cut it to length, then trim the blade to shape.

चाहिने औजार:

पिट्ने घनपिट्ने घन
सम्म पार्ने औजारसम्म पार्ने औजार
तातो छिनोतातो छिनो
4

Anneal and grind

Heat to a full red and anneal in lime or ashes. When cold, grind on an emery wheel and finish on a buffing wheel.

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
टेबुलको घोट्ने मेसिनटेबुलको घोट्ने मेसिन
5

Harden and temper

Heat very slowly to the hardening heat and cool in tepid water. Draw the temper with two hot iron bars laid on either side at the centre; when the blade is dark purple and the head blue, cool quickly in water.

चाहिने औजार:

आरनको भट्टीआरनको भट्टी
पानी दिने बाल्टिनपानी दिने बाल्टिन
आरनको सँड़सीआरनको सँड़सी
6

Handle

Shave the handle stock to fit the eye tightly, drive the head on, saw a kerf in the handle's top and drive a glued hardwood wedge into it. Trim flush and oil the handle.

यस चरणका सामग्री:

बीँडका लागि कडा काठबीँडका लागि कडा काठ1 टुक्रा
कडा काठको चेप्टो किलाकडा काठको चेप्टो किला1 टुक्रा
अलसीको तेलअलसीको तेल10 मिलि

चाहिने औजार:

दुई बिँडको रन्दादुई बिँडको रन्दा
दुई जनाको आडा आरादुई जनाको आडा आरा
बेन्चको भाइसबेन्चको भाइस

सामग्री

4

आवश्यक उपकरणहरू

16

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...