सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Gas Burner: a Home-Made Bunsen Burner from Brass Tube (Work, 1892)
Charlie

सिर्जनाकर्ता

Charlie

7. नोभेम्बर 2026DE
११
०
०
०
०

Gas Burner: a Home-Made Bunsen Burner from Brass Tube (Work, 1892)

A Bunsen burner: gas from a fine jet draws air in through two holes at the foot of an upright tube, and the mixture burns at the top with a hot blue flame that leaves no soot. H. B. Stocks (Work, 1892) makes one from a 3 1/2 in. brass tube 1/2 in. across, a short 3/8 in. tube for the gas, a brass boss and elbow from a gas bracket, and a bit of fine-bore tube from an old oil-can as the jet. A sliding brass collar over the air-holes sets the flame. Source: H. B. Stocks, How to Make a Cheap Spirit Lamp, Bunsen Burner, Blowpipes, etc., Work No. 167 (28 May 1892), p. 167. Picture: his Figs. 3-4.
मध्यम
Unknown

निर्देशनहरू

1

Read Stocks

"To make a Bunsen burner the following materials will be necessary:—A piece of brass tube 3 1/2 in. long, 1/2 in. diameter (external); a piece of tube 3/8 in. in diameter, 1 1/2 in. long; a brass boss similar to those on an ordinary bracket, but without a tap; a brass elbow tube; also a piece of tubing with very fine bore (small bit of tube from an old oil-can will do)."
2

Solder the elbow on the boss

Solder the brass elbow-piece onto the brass boss, with the tube that has a screw cut for a gallery uppermost.

यस चरणका सामग्री:

चुरोदार पाइप फिटिङचुरोदार पाइप फिटिङ2 boss and elbow
टिन-सिसाको टाँकाटिन-सिसाको टाँका1 joint
फ्लक्सफ्लक्स1 joint

चाहिने औजार:

टाँका लगाउने डन्डीटाँका लगाउने डन्डी
3

Fit the jet

Cut the fine-bore tube 3/4 in. to 1 in. long and solder it inside the vertical tube of the elbow-piece so it projects about 1/2 in. If it is too small for the hole, plug round it with a little sheet lead, keeping it perfectly vertical and in the centre of the outer tube, then solder. The metal of the oil-can tube is not given (unknown).

यस चरणका सामग्री:

अज्ञात धातुअज्ञात धातु1 fine-bore tube
सिसा धातुको पातासिसा धातुको पाता1 packing
टिन-सिसाको टाँकाटिन-सिसाको टाँका1 joint

चाहिने औजार:

टाँका लगाउने डन्डीटाँका लगाउने डन्डी
पाता काट्ने कैँचीपाता काट्ने कैँची
4

Make the burner tube

Take the brass tube 3 1/2 in. long, 1/2 in. across. If it is not of very thick brass it will be a little too large: turn a piece of very thin sheet brass 1/2 in. by 1 1/4 in. into a cylinder and solder it inside one end. Tap that end inside to screw onto the male thread of the elbow-piece. At the same end drill two holes about 3/8 in. across, exactly opposite each other, their centres 5/8 in. from the end: the air-holes.

यस चरणका सामग्री:

पित्तलको नली, बाहिरी व्यास १/२ इन्चपित्तलको नली, बाहिरी व्यास १/२ इन्च1 3 1/2 in.
पित्तलको पातापित्तलको पाता1 1/2 x 1 1/4 in.
टिन-सिसाको टाँकाटिन-सिसाको टाँका1 joint

चाहिने औजार:

पाता काट्ने कैँचीपाता काट्ने कैँची
टाँका लगाउने डन्डीटाँका लगाउने डन्डी
चुरो काट्ने सेटचुरो काट्ने सेट
ट्याप घुमाउने ह्यान्डलट्याप घुमाउने ह्यान्डल
हाते ड्रिलहाते ड्रिल
5

Assemble and test

Screw the burner tube onto the elbow-piece and screw the 3/8 in. tube, 1 1/2 in. long, into the side opening. Push the india-rubber tube from the gas supply onto the side tube and light. A purplish-blue flame means air and gas are in the right proportion. A yellow tip means too much gas: plug the hole in the jet slightly.

यस चरणका सामग्री:

पित्तलको नली, बाहिरी व्यास ९.५ मिमीपित्तलको नली, बाहिरी व्यास ९.५ मिमी1 1 1/2 in.

चाहिने औजार:

रबरको नलीरबरको नली
6

Fit the air collar

If the gas burns with a green flame and a hissing noise, the air-holes are too large. Cut sheet brass about 3/4 in. wide and 1 3/4 in. long and drill two holes 3/8 in. across, 1/2 in. from each end (their centres 3/16 in. further in). Turn it into a tube and push it onto the burner tube over the air-holes. Turn it until the two sets of holes do not quite match, so the right amount of air reaches the burner.

यस चरणका सामग्री:

पित्तलको पातापित्तलको पाता1 3/4 x 1 3/4 in.

चाहिने औजार:

पाता काट्ने कैँचीपाता काट्ने कैँची
हाते ड्रिलहाते ड्रिल

सामग्री

8

आवश्यक उपकरणहरू

6

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...