कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Glass Fibre Mat: Blown Glass Wool Drafted into a Bonded Sheet (Slayter 1942)
Blown glass wool lands on a moving screen as a loose, weak tangle. Slayter pulled a thin web off its front edge two to four times faster than the screen moves, so the fibres line up lengthwise but still cross each other, and then soaked and dried it in a binder. The result is a thin, even, strong glass sheet, used for insulation, filters and separators between battery plates.
Source: Games Slayter (Owens-Corning Fiberglas), US 2,306,347 (1942). Unknown: the glass and the binder. Slayter names neither the glass nor the binder's strength, so both are linked to unknown heads. Speeds and temperatures are not given either. Picture: the patent's Fig. 1.
उन्नत
continuous
निर्देशनहरू
1
1
Blow fibres from the bushing
Blow fibres from the bushing
Let molten glass run in many streams from one or more electrically heated bushings. Gas blasts from jets around the streams draw them out into long, fine fibres, which set at once as they fall through a forming hood. Unknown: the glass, the bushing temperature and the blast. Slayter gives none of them.
यस चरणका सामग्री:
अज्ञात काँच1 as requiredचाहिने औजार:
काँच-रेसा बुसिङ
स्टेप-डाउन ट्रान्सफर्मर
रूपण हुड
ताप सहने पन्जा
सुरक्षा चस्मा2
2
Collect a mat on a moving screen
Collect a mat on a moving screen
The fibres land on an endless wire screen running over rollers, with a suction box under it to draw off the blast and hold the fibres down. They pile up in every direction as a mat. If you like, spray a lubricant into the hood first (oil, soap, fatty acid, glycerin or graphite are named), so the fibres slide past each other when drafted.
चाहिने औजार:
जाली कन्भेयर
हावा फाल्ने यन्त्ररूपण हुड3
3
Draft a web off the front edge
Draft a web off the front edge
Pull a thin web from the front edge of the mat over an idler roller set slightly above the screen, faster than the screen moves. Slayter recommends a 3 to 1 draft for long fibres and 2 to 1 up to 4 to 1 in general. The fibres turn mostly lengthwise but stay crossed, which holds the sheet together across its width.
चाहिने औजार:
तन्काउने रोलरजाली कन्भेयर4
4
Soak it in binder between the drafting rolls
Soak it in binder between the drafting rolls
Lead the web down under the surface of a pool of binder solution and between the drafting pinch rolls. The lower roll is perforated and half under the liquid. The rolls set the draft through a variable-speed drive and squeeze out the excess binder, which runs back into the tank. Unknown: the binder. For battery separators Slayter wants one that keeps the sheet porous: 'a relatively weak solution' of phenolic resin, rubber, starch, gelatin, polystyrene or methyl methacrylate, with no strength given.
यस चरणका सामग्री:
अज्ञात बाइन्डर1 as requiredचाहिने औजार:
तन्काउने रोलर5
5
Dry it under slight tension
Dry it under slight tension
Pull the wet sheet through a drying oven with a second pair of pinch rolls, blowing heated air through against the sheet's direction. Keep only a slight draft, 1.05 to 1 up to 1.5 to 1, so the sheet neither wrinkles across nor stretches lengthwise as the binder sets. Unknown: the oven temperature. Wind the dry mat onto a roll.
चाहिने औजार:
सुकाउने भट्टीतन्काउने रोलरहावा फाल्ने यन्त्रसामग्री
2- 1 as requiredप्लेसहोल्डर
- 1 as requiredप्लेसहोल्डर
आवश्यक उपकरणहरू
9- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
यो खाकाले बनाउँछ
सम्बन्धित ब्लुप्रिन्ट
यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त
CC0 सार्वजनिक डोमेन
यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।
ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।