सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Chinese Dragon Kite: Bamboo-Ring Head With Revolving Eyes and 20 Sections on a Seine-Twine Harness (Boy Mechanic, 1919)
Spartan

सिर्जनाकर्ता

Spartan

13. नोभेम्बर 2026NO
९
०
०
०
०

Chinese Dragon Kite: Bamboo-Ring Head With Revolving Eyes and 20 Sections on a Seine-Twine Harness (Boy Mechanic, 1919)

C. M. Miller's dragon kite from The Boy Mechanic, Book 3 (1919): a 12 in bamboo-ring head with horns and two paper eyes that spin in the wind, followed by up to 20 round section kites, each with a 36 in balancer stick, tied 30 in apart on three cords of seine twine. Twenty sections make a kite about 50 ft long.
उन्नत
Several days

निर्देशनहरू

1

Strip lengths and kite length

Jupyter नोटबुक लोड हुँदैछ…
2

Read The Boy Mechanic, Book 3

"Dragon kites are made as hideous as the maker can possibly conceive, and while the one to be considered is no beauty, it is more droll than fierce-looking."
3

Split and pare the bamboo

Split bamboo into strips about 3/16 in wide and pare them to less than 1/16 in thick for the head's inner ring A. To bend a strip to a sharp angle, heat it over a candle flame until it gives under pressure, bend it, and it keeps its shape when cold.

यस चरणका सामग्री:

बाँसका लिँडेबाँसका लिँडे1 टुक्रा

चाहिने औजार:

इस्पात खल्तीको चक्कुइस्पात खल्तीको चक्कु
मैनबत्तीमैनबत्ती
4

Frame the head

Make ring A 12 in across from a strip about 38 in long, lapping the ends and winding them with linen thread (or with wet pasted strips of rice paper about 1/2 in wide, which bind as they dry). Lash two crosspieces B and C of the same stock 3-1/2 in apart, parallel and equally spaced from the centre, their ends bent sharply and lashed inside the ring. Lash two eye rings D and E, 3-1/2 in across, between them, shaped round a 3-1/2 in cylinder so they are true. Lash stiffeners F and G, 1/16 by 1/8 by 20 in, across the back. Add outer ring H, 3 in outside A (18 in across), of 1/8 in strip under 1/16 in thick, in two pieces if needed, and the short pieces J and K between the rings. Lash the horn supports, 1/8 in wide, to the upper crosspiece and both rings, with L and M halfway between the ends of F and G and radiating from the centre of A, and N and O pointing at the eye-ring centres (Fig. 2).

यस चरणका सामग्री:

बाँसका लिँडेबाँसका लिँडे1 टुक्रा
लिनेनको धागोलिनेनको धागो1 टुक्रा

चाहिने औजार:

इस्पात खल्तीको चक्कुइस्पात खल्तीको चक्कु
मैनबत्तीमैनबत्ती
नाप्ने फित्तानाप्ने फित्ता
कैँचीकैँची
5

Cover and paint the head

Cover only the inside of ring A, the horns and the ears with Chinese rice paper, stretched tight with no bagging, leaving the eye rings open. Put the rings on the horns and stick ends, 1/2 to 2 in across, cut from stiff paper (larger ones of bamboo). Shade with a brush and water colours, leaving the face white or tinting it; leave the horns white and colour the tongue red (Fig. 1).

यस चरणका सामग्री:

राइस पेपरराइस पेपर1 टुक्रा
गहुँको पिठोको लेदोगहुँको पिठोको लेदो1 टुक्रा
बाक्लो कागजबाक्लो कागज1 टुक्रा
जलरङजलरङ1 टुक्रा

चाहिने औजार:

गोन्दको ब्रसगोन्दको ब्रस
कलाकारका बुरुसको सेटकलाकारका बुरुसको सेट
कैँचीकैँची
6

Make the revolving eyes

Pare bamboo to 1/32 in and form each eye into a true ring 3-1/4 in across. Pass a wire axle exactly on a diameter through the eye ring and through its socket ring D or E, with a glass bead on the wire each side between the two rings; fix the wire to the eye ring with a strip of paper wrapped tight and pasted. Cover each side halfway with rice paper, the front upper half and the back lower half, so the wind turns the eye. Blacken the front upper half and paste a round pupil between the halves so it shows on both sides (Figs. 3, 4).

यस चरणका सामग्री:

बाँसका लिँडेबाँसका लिँडे1 टुक्रा
फलामे तारफलामे तार1 टुक्रा
सिसाका मणिसिसाका मणि4 टुक्रा
राइस पेपरराइस पेपर1 टुक्रा
गहुँको पिठोको लेदोगहुँको पिठोको लेदो1 टुक्रा
जलरङजलरङ1 टुक्रा

चाहिने औजार:

इस्पात खल्तीको चक्कुइस्पात खल्तीको चक्कु
चेप्टो मुखको प्लासचेप्टो मुखको प्लास
कैँचीकैँची
कलाकारका बुरुसको सेटकलाकारका बुरुसको सेट
7

Make the section kites

For each section make a 12 in ring of bamboo 1/8 in wide and 1/16 in thick and cover it tight like the head. Lash on a balancer stick 36 in long, small, light and well balanced, at about the place of cross-stick F, with tufts of tissue paper or feathers at its tips. Colour the discs as you like; give the last section's balancer streamers of light cloth (Figs. 5, 6). Sections may instead be 9 in with 30 in balancers, but uniform sections are better and easier.

यस चरणका सामग्री:

बाँसका लिँडेबाँसका लिँडे1 टुक्रा
लिनेनको धागोलिनेनको धागो1 टुक्रा
राइस पेपरराइस पेपर1 टुक्रा
गहुँको पिठोको लेदोगहुँको पिठोको लेदो1 टुक्रा
रङ्गीन टिस्यु कागजरङ्गीन टिस्यु कागज1 टुक्रा
प्वाँखप्वाँख1 टुक्रा
सुतीको कपडासुतीको कपडा1 टुक्रा
जलरङजलरङ1 टुक्रा

चाहिने औजार:

इस्पात खल्तीको चक्कुइस्पात खल्तीको चक्कु
मैनबत्तीमैनबत्ती
कैँचीकैँची
कलाकारका बुरुसको सेटकलाकारका बुरुसको सेट
8

Tie the harness and bridle

Cut three cords of six-ply hard-twisted seine twine as long as the kite plus the knots. Fasten the head to a wall, tie the three cords to it at T, U and V (Fig. 2), and tie each section at the matching points exactly 30 in from the last (Fig. 7). Tie a three-string bridle to the head at T, U and V, the lower string longer than the two upper ones so the head, and with it every section, leans to the wind. A ball balancer of bamboo strips may hang from the head (Fig. 8).

यस चरणका सामग्री:

जाल बुन्ने सुतलीजाल बुन्ने सुतली1 टुक्रा
चङ्गाको धागोचङ्गाको धागो1 टुक्रा
बाँसका लिँडेबाँसका लिँडे1 टुक्रा

चाहिने औजार:

नाप्ने फित्तानाप्ने फित्ता
कैँचीकैँची
9

Flying and troubleshooting

Dragon kite flying.

Flow

Loading...
10

History and honest limits

From "How to Make Combined Kites, Part I: A Dragon Kite" by C. M. Miller, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 145-148). He gives no bridle lengths and no line size beyond "a strong cord". Fig. 2 also marks 5 in at the horn tip and 1 in where F passes ring H. The tools and metric figures are ours.

सामग्री

13

आवश्यक उपकरणहरू

7

यो खाकाले बनाउँछ

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...