सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
PTFE Sheet: Compact-Extruded Films, Sintered, Laid at 45° and Fused (MacFarland, Hills-McCanna, US 3,130,954)
Charlie

सिर्जनाकर्ता

Charlie

31. अक्टोबर 2026DE
१०
०
०
०
०

PTFE Sheet: Compact-Extruded Films, Sintered, Laid at 45° and Fused (MacFarland, Hills-McCanna, US 3,130,954)

Thick PTFE was cut from a sintered billet with a knife, and the skived sheet tore along the knife marks. MacFarland built his sheet up instead, from thin extruded films laid crosswise and fused together, for the liner of a valve diaphragm. Result: a dense PTFE sheet, about 7,000 psi tensile and 450 % elongation, much the same in every direction. Source: MacFarland, US 3,130,954 (Hills-McCanna, 1964). Not given: furnace temperature, mill pressure. Picture drawn by Youblob.
उन्नत
Factory process

निर्देशनहरू

1

Compact-extrude a film

Feed finely divided PTFE resin from a hopper through a screw extruder to a slot die, usually without added heat. It comes out as a compact film that holds together unsintered, up to 24 in wide.

यस चरणका सामग्री:

PTFE रेजिनको धूलोPTFE रेजिनको धूलो1 as required

चाहिने औजार:

प्लास्टिक एक्सट्रुडरप्लास्टिक एक्सट्रुडर
एक्स्ट्रुजन डाइएक्स्ट्रुजन डाइ
2

Sinter and coin the film

Carry the film through a sintering furnace to its fusion (gel) state and coin it in a mill as it goes. It comes out dense, with few pores, 5-8 mils thick. Ours: muffle furnace and calender rolls.

चाहिने औजार:

मफल भट्टीमफल भट्टी
चिल्ला क्यालेन्डर रोलहरूचिल्ला क्यालेन्डर रोलहरू
3

Lay the films crosswise and fuse them

Each film is a little stronger lengthwise, so stack several with their lengthwise axes turned by the same angle each time; 45° works well (MacFarland shows five plies). Feed the stack into a final sintering and compacting mill to fuse it into one sheet (over 20 mils thick). Ours: muffle furnace and calender rolls.

चाहिने औजार:

मफल भट्टीमफल भट्टी
चिल्ला क्यालेन्डर रोलहरूचिल्ला क्यालेन्डर रोलहरू

सामग्री

1

आवश्यक उपकरणहरू

4

यो खाकाले बनाउँछ

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...