सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Rubber Compound: Raw Rubber Washed, Dried and Mixed with Sulphur on Hot Rolls (Thorpe, 1913)
Charlie

सिर्जनाकर्ता

Charlie

4. नोभेम्बर 2026DE
११
०
०
०
०

Rubber Compound: Raw Rubber Washed, Dried and Mixed with Sulphur on Hot Rolls (Thorpe, 1913)

How a rubber works of 1913 turned raw rubber into a 'mixing' ready for shaping and curing: the rubber is washed between corrugated rolls under running water, dried on racks, broken down on hot smooth rolls until plastic, and then worked together with fillers and finally sulphur into an even dough. Very few goods were made of rubber and sulphur alone: pure mixings cost too much and are too soft for most uses. Unknown: which fillers, and how much of them and of sulphur. Thorpe names the kinds of materials but gives no mixing. Source: T. E. Thorpe, Dictionary of Applied Chemistry vol. IV (1913), pp. 586-587. Picture: Fig. 1, a washing machine.
मध्यम
3-4 days drying

निर्देशनहरू

1

Steep and wash the rubber

Cut the raw rubber into lumps or slabs and steep them for some hours in warm water. Pass them again and again through corrugated, diamond-cut or fluted rolls running at a speed difference of 6 : 4 down to one tooth, with a stream of water on the rubber, until the rough crepe-like sheet is clean and thin.

यस चरणका सामग्री:

धुवाँमा सुकाएको रबरको पाताधुवाँमा सुकाएको रबरको पाता1 raw rubber
पानीपानी1 warm, then running

चाहिने औजार:

दुई-रोलर रबर मिलदुई-रोलर रबर मिल
2

Dry on racks

Hang the sheet on racks in a drying room until it holds only about 0.25-0.5 per cent moisture: about 3-4 days at about 80°F with good ventilation. Cooler, drier air is better, as warm rubber turns soft and tacky.

चाहिने औजार:

सुकाउने र्‍याकसुकाउने र्‍याक
3

Break it down

Pass the dry rubber repeatedly through the steam-heated smooth rolls of the mixing machine, which run at different speeds, tightening the rolls gradually until the rubber is thoroughly plastic.

चाहिने औजार:

दुई-रोलर रबर मिलदुई-रोलर रबर मिल
4

Mix in the fillers and sulphur

Add the other materials gradually: reclaimed rubber, ground waste, 'substitute' and other organic fillers first, then the minerals and the sulphur last. Work it into a thoroughly even dough without overworking ('tiring') the rubber.

यस चरणका सामग्री:

अज्ञात सामग्रीअज्ञात सामग्री1 fillers and minerals; not given
गन्धकको धूलोगन्धकको धूलो1 amount not given

चाहिने औजार:

दुई-रोलर रबर मिलदुई-रोलर रबर मिल

सामग्री

4

आवश्यक उपकरणहरू

2

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...