सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring
Forge

सिर्जनाकर्ता

Forge

26. अक्टोबर 2026NO
२६
०
०
०
०

Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring

A screw eye bent from one piece of wire, by Arthur W. Parmelee of Worcester, Massachusetts (US 350,209, 1886). One end is threaded to turn into wood, the other bent into a closed eye. His addition is a ring closed into a groove around the shank: it stops the screw at the right depth, looks neat, and is left a little loose so the eye can turn without marking the wood under it. The patent gives no metal or sizes. Iron wire, the 3 mm size, the pliers and the die are ours. The picture: Figs. 1-3 and 10-11 of the patent.
शुरुआती
30 minutes

निर्देशनहरू

1

Cut a piece of wire

Cut a straight piece of iron wire about 3 mm thick (ours), long enough for the screw, the shank and the eye (Fig. 1).

यस चरणका सामग्री:

फलामे तारफलामे तार1 टुक्रा

चाहिने औजार:

रुलररुलर
तर्छो तार काट्ने प्लासतर्छो तार काट्ने प्लास
2

Cut the groove

File a narrow groove right round the wire, a screw length from one end (Fig. 2). Parmelee cuts it or presses it in.

चाहिने औजार:

सियो-रेतीको सेटसियो-रेतीको सेट
बेन्चको भाइसबेन्चको भाइस
3

Point the screw end

File that end to a tapering point (Fig. 3).

चाहिने औजार:

धातुको रेतीधातुको रेती
बेन्चको भाइसबेन्चको भाइस
4

Thread the screw end

Cut a screw thread on the pointed end "in the usual way". Ours: a die in a die stock, run on as far as the point allows.

चाहिने औजार:

डाइ समात्ने ह्यान्डलडाइ समात्ने ह्यान्डल
बेन्चको भाइसबेन्चको भाइस
5

Bend the eye

Bend the other end into a closed round eye, the end turned in against the shank (Fig. 10).

चाहिने औजार:

गोलो मुखको प्लासगोलो मुखको प्लास
चेप्टो मुखको प्लासचेप्टो मुखको प्लास
6

Make the split ring

Bend a short piece of the same wire round into an open ring that just slips over the shank (Figs. 9 and 11).

यस चरणका सामग्री:

फलामे तारफलामे तार1 टुक्रा

चाहिने औजार:

तर्छो तार काट्ने प्लासतर्छो तार काट्ने प्लास
गोलो मुखको प्लासगोलो मुखको प्लास
7

Close the ring into the groove

Slide the ring onto the groove and squeeze it until its two ends meet in a continuous band. Leave it a little loose, so the eye turns while the ring stays still against the wood.

चाहिने औजार:

चेप्टो मुखको प्लासचेप्टो मुखको प्लास
8

Turn it into the wood

Turn the screw into the wood by the eye until the ring meets the surface: the ring is the depth stop. Parmelee also allows washers under the ring; we leave them out.

सामग्री

1
  • 2 टुक्रा
    प्लेसहोल्डर

आवश्यक उपकरणहरू

8

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...