कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
हरित भविष्य
रिभर्स इन्जिनियरिङ
विद्यालय परियोजनाहरू
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Using a Piezo Buzzer — SIK Circuit 11
Ed

सिर्जनाकर्ता

Ed

17. मार्च 2026FI
७७
०
०
०
०

Using a Piezo Buzzer — SIK Circuit 11

Play a song with a piezo buzzer! Learn about the tone() function, musical frequencies, arrays for storing melodies, and how to create your own tunes.

निर्देशनहरू

1

Parts & Introduction

A piezo buzzer converts electrical signals into sound. Using Arduino's built-in tone() function, you can play specific musical frequencies. This sketch plays a simple melody using character arrays for notes and integer arrays for timing.

Parts Needed

  • 1x Arduino Uno + USB cable
  • 1x Breadboard
  • 1x Piezo Buzzer
  • 3x Jumper Wires

Note Frequency Reference

NoteFreq
c262 Hz
d294 Hz
e330 Hz
f349 Hz
g392 Hz
a440 Hz
b494 Hz
C523 Hz

Materials for this step:

SparkFun Inventors Kit - V3.2SparkFun Inventors Kit - V3.21 किट
Arduino Uno R3Arduino Uno R31 टुक्रा
BreadboardBreadboard1 टुक्रा
Piezo Buzzer1 टुक्रा
Jumper WiresJumper Wires2 टुक्रा

Tools needed:

Computer with Arduino IDE
2

Hardware Hookup

Wiring Instructions

  1. Place the piezo buzzer in the breadboard. It has two pins — one marked with "+".
  2. Connect the positive pin (+) to Arduino Digital Pin 9 (PWM).
  3. Connect the negative pin to GND.

Tip: If the buzzer doesn't fit easily, try rotating it slightly to align with diagonal breadboard holes.

Materials for this step:

Piezo Buzzer1 टुक्रा
BreadboardBreadboard1 टुक्रा
Jumper WiresJumper Wires2 टुक्रा
3

Arduino Code

Open the Arduino IDE and upload the following sketch to your Arduino board.

piezo_buzzer.inoarduino
/*
SparkFun Inventor's Kit
Example sketch 11 — BUZZER

Use the buzzer to play a song!

Hardware connections:
  Buzzer positive pin (+) to digital pin 9 (PWM)
  Buzzer negative pin to GND

This code is completely free for any use.
*/

const int buzzerPin = 9;

const int songLength = 18;

char notes[] = "cdfda ag cdfdg gf ";  // space = rest

int beats[] = {1,1,1,1,1,1,4,4,2,1,1,1,1,1,1,4,4,2};

int tempo = 113;

void setup()
{
  pinMode(buzzerPin, OUTPUT);
}

void loop()
{
  int i, duration;

  for (i = 0; i < songLength; i++)
  {
    duration = beats[i] * tempo;

    if (notes[i] == ' ')
    {
      delay(duration);
    }
    else
    {
      tone(buzzerPin, frequency(notes[i]), duration);
      delay(duration);
    }
    delay(tempo/10);
  }

  while(true){}  // Play once, then stop. Remove this line to loop.
}

int frequency(char note)
{
  int i;
  const int numNotes = 8;

  char names[] = { 'c', 'd', 'e', 'f', 'g', 'a', 'b', 'C' };
  int frequencies[] = {262, 294, 330, 349, 392, 440, 494, 523};

  for (i = 0; i < numNotes; i++)
  {
    if (names[i] == note)
    {
      return(frequencies[i]);
    }
  }
  return(0);
}

Materials for this step:

Arduino Uno R3Arduino Uno R31 टुक्रा

Tools needed:

Computer with Arduino IDE
4

Test & Experiment

What You Should See

You won't see anything — but you'll hear a melody playing from the buzzer! The song plays once and stops.

Troubleshooting

  • No sound: The buzzer pins are easy to misplace on the breadboard. Double-check placement and make sure both pins have good contact.
  • Want it to stop: Pull the buzzer out while working on other things, plug it back in to test.

Experiments to Try

  • Remove the while(true){} line to make the song loop continuously.
  • Write your own melody by changing the notes[] and beats[] arrays.
  • Add more notes by expanding the frequency() function with sharps and flats.
  • Use a button (from Circuit 5) to trigger the melody on demand.

सामग्री

5

आवश्यक उपकरणहरू

1
  • 13
    Computer with Arduino IDE
Estimated Total
$120.00

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

Recommended for this build

Products makers often use with builds like this one.

Resistor 330 Ohm 1/6 Watt PTH - 20 packUsed together and in similar builds
5mm LED Assortment Kit (300pcs, 5 Colors)Used together and in similar builds
Push Button - 33mmUsed together and in similar builds
Basic 16x2 Character LCD - 5VUsed in similar builds
Resistor 10K Ohm 1/6th Watt PTH - 20 packUsed together and in similar builds
PotentiometerUsed together and in similar builds
Servo MotorFrequently used with this build's materials
LED - RGB Diffused Common Cathode - 5mmFrequently used with this build's materials

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Using an LCD — SIK Circuit 15electronics1 shared material
Simon Says — SIK Circuit 16electronics1 shared material
Push Buttons — SIK Circuit 5electronics1 shared material
Using a Flex Sensor — SIK Circuit 9electronics/electromech1 shared material
Using a Shift Register — SIK Circuit 14electronics/active1 shared material
Driving a Servo Motor — SIK Circuit 8electronics/electromech1 shared material

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...