सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)
Forge

सिर्जनाकर्ता

Forge

15. नोभेम्बर 2026NO
५
०
०
०
०

Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)

Alfred Soward's laboratory cork-borer from Amateur Work (1881): about 4 in. of brass tube the size of the hole, one end filed on the outside to a ring-shaped cutting edge, a brass flange on the other end to strengthen it, and a steel wire pushed through a cross hole as a handle. Turned like a gimlet, it cuts a clean, centred hole for a glass tube.
शुरुआती
An hour

निर्देशनहरू

1

Read Soward

"This latter instrument is simply a piece of brass tube about 4 in. long, and of a diameter suited to the hole required."
2

Cut the tube

Cut about 4 in. (100 mm) of brass tube whose outside diameter matches the hole you need (he takes 3/8 in., about 10 mm, for a glass tube). Square both ends.

यस चरणका सामग्री:

पित्तलको नलीपित्तलको नली1 टुक्रा

चाहिने औजार:

बेन्चको भाइसबेन्चको भाइस
फलाम काट्ने आराफलाम काट्ने आरा
रेती (हातको रेती)रेती (हातको रेती)
3

File the cutting edge

File one end on the outside only, all round, to a thin cutting edge: like two gouges put together with their hollow sides facing (B in his fig. 7). Leave the bore untouched.

चाहिने औजार:

बेन्चको भाइसबेन्चको भाइस
रेती (हातको रेती)रेती (हातको रेती)
सियो रेतीसियो रेती
4

Fit the flange

Fit a small brass ring or flange round the other end to strengthen it (D in fig. 7). Ours: cut it from brass sheet and soft-solder it on.

यस चरणका सामग्री:

पित्तलको पातापित्तलको पाता1 टुक्रा
सोल्डर तारसोल्डर तार1 टुक्रा
फ्लक्सफ्लक्स1 टुक्रा

चाहिने औजार:

पाता काट्ने कैँचीपाता काट्ने कैँची
खम्बा भएको ड्रिलखम्बा भएको ड्रिल
ड्रिल टुप्पाको सेटड्रिल टुप्पाको सेट
टाँका लगाउने डन्डीटाँका लगाउने डन्डी
5

Cross hole and handle

Below the flange, drill a hole straight across the tube for a piece of steel wire. Push the wire through so it stands at right angles to the tube as a handle (C in fig. 7, drawn with a head on one end).

यस चरणका सामग्री:

इस्पातको तारइस्पातको तार1 टुक्रा

चाहिने औजार:

खम्बा भएको ड्रिलखम्बा भएको ड्रिल
ड्रिल टुप्पाको सेटड्रिल टुप्पाको सेट
रेती (हातको रेती)रेती (हातको रेती)
6

Troubleshooting

Cork borer troubleshooting.

Flow

Loading...
7

History and honest limits

From Alfred W. Soward, "Filters: Their Construction and Maintenance" I, **Amateur Work, Illustrated**, vol. I (1881), pp. 131-133 and fig. 7 (checked on the archive.org scan amateurworkillus11881lond). To use it, hold the cork's small end against a wall or the bench edge, press on the centre of the large end and turn like a gimlet, giving the cork a quarter turn left after each quarter turn of the borer right. A bought set of four then cost 1s. He does not say how the flange is fixed: soft solder, the metric figures and the tools are ours.

सामग्री

5
  • प्लेसहोल्डर
  • प्लेसहोल्डर
  • 1 टुक्रा
    प्लेसहोल्डर
  • 1 टुक्रा
    प्लेसहोल्डर
  • प्लेसहोल्डर

आवश्यक उपकरणहरू

8

सम्बन्धित ब्लुप्रिन्ट

यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...