सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने

16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)
Stillman Taylor's open Canadian canoe from The Boy Mechanic, Book 3 (1919): about 16 ft long, 31 in beam, 60 to 70 lb. Built upside down over a backbone and seven paper-pattern molds, with oak or ash stems, keelson and gunwales, 1/8 in cedar ribs and planking fastened with copper clout nails, then covered with No. 6 canvas laid in melted marine glue, painted, and varnished. Every layout dot and width is his, as printed.
उन्नत
Several weeks
निर्देशनहरू
1
1
His layout data
His layout data
Jupyter नोटबुक लोड हुँदैछ…
2
2
Read The Boy Mechanic, Book 3
Read The Boy Mechanic, Book 3
"Working with light materials, the canoe builder must pay particular attention to the workmanship ... the work must not be hurried, but plenty of time taken to do each and every part well."
3
3
Get the materials
Get the materials
Stem: oak or ash 6 ft x 3/4 in square. Keelson: oak or ash 14 ft x 3-1/2 x 3/8 in. Gunwales: 2 of oak or ash 16 ft x 7/8 x 1/2 in. Seat risings: 2 of oak or ash 1/2 in square. Fenderwales: 34 ft of 1/2 in half-round molding. Outside keel (optional): oak 14 ft x 1 x 1/2 in. Deck beams: 2 of oak or ash 8 x 1-1/8 x 3/8 in. Seat frames: 2 at 30 x 3 x 3/4 and 2 at 12 x 2-1/4 x 3/4 in. Planking: cedar or pine, 100 sq ft, 1/8 in (25 ft of 1 in lumber dressed to 1/8 in, in 12, 14 and 16 ft lengths). Ribs: 360 running ft of cedar 1-3/4 x 1/8 in. Breast hooks: cedar or oak 32 x 9 x 3/4 in. Backbone, molds and ribbands from any cheap stuff. Fastenings: 1 lb 2 in wire nails; 1 lb 5/8 in and 1/2 lb 3/4 in copper clout nails; 18 brass screws 1-1/4 in No. 8 and 24 brass screws 1 in No. 6; 4 lb marine glue; 3 oz No. 2 copper tacks; 11-3/4 yd No. 6 canvas; 1 lb 3/8 in copper tacks. Rock elm or fir may replace oak or ash; spruce, pine, cypress or fir may replace cedar.
यस चरणका सामग्री:
सेतो फलाँटको फल्याक4 टुक्रा
सिडरको फल्याक6 टुक्रा
सल्लाको फल्याक3 टुक्राचाहिने औजार:
चिराइ आरा
हाते आरा
रन्दा
नाप्ने फित्ता4
4
Lay out the backbone and molds
Lay out the backbone and molds
Cut the backbone from a 16 ft x 4 x 7/8 in board, top edge 15 ft 8-3/4 in, and mark the mold stations from each end: 22-1/4 in to mold 1, then 23-1/4 in to mold 2 and 23-1/4 in to mold 3, each mold space 3/4 in thick; mold 4 sits at the centre; cut the ends off on the bevel (Fig. 1). Draw each mold on stiff paper from his rectangles, mortises and dots (notebook), trace the curve through the dots, cut out the half, fold and draw the other side, and cut the molds from 7/8 in stock: seven in all, numbered alike from each end: two No. 1, two No. 2 (each in halves), two No. 3 and one No. 4; nail battens across the halves.
यस चरणका सामग्री:
सल्लाको फल्याक2 टुक्रा
बाक्लो कागजका पाना1 टुक्रा
काँटी1 टुक्राचाहिने औजार:
हाते आरा
वक्र काट्ने आरा
रुलर
सिसाकलम
कैँची
घन5
5
Bend the stems and shape the keelson
Bend the stems and shape the keelson
Make the stem mold from his Fig. 6 pattern (24-1/2 x 12 in rectangle, dots in the notebook) and bend the straight-grained 3/4 in square oak or ash stems on it. Cut the keelson 13 ft 11 in long, tapering from 3-1/2 in at the centre: 3-1/2 in at 1 and 2 ft, 3-1/4, 2-5/8, 2 and 1-1/4 in at 3 to 6 ft, and 15/16 in at the ends (Fig. 7). Fasten each stem to the keelson with a couple of 3/4 in No. 10 screws.
यस चरणका सामग्री:
सेतो फलाँटको फल्याक2 टुक्रा
पित्तलका काठ पेच4 टुक्राचाहिने औजार:
दुई बीँडको तान्ने चक्कु
रन्दा
हाते आरा
हातले घुमाउने ड्रिल र बिट
पेचकिला - चेप्टो
सी-आकारको क्ल्याम्प6
6
Set up the frame
Set up the frame
Build it upside down: set the backbone on boxes about 1 ft or more off the floor and the molds in their numbered places, the backbone resting in their top mortises. True the molds with a square and toenail them. Lay the keelson in its mortises, fit the stems to the backbone angle and nail through the mold tops into them. Bevel the stem splice from the inside, leaving the outer edge about 1/8 in wide. Put on the gunwales at the sheer line with nails left proud, then four ribbands a side at 5 in centres from the keel, fastened with 1-1/4 in brads.
यस चरणका सामग्री:
सेतो फलाँटको फल्याक2 टुक्रा
सल्लाको फल्याक1 टुक्रा
काँटी1 टुक्राचाहिने औजार:
स्थिर गुनिया
घन
छिनाहरू
रन्दा7
7
Rib the hull
Rib the hull
Saw cedar ribs 1-3/4 in wide and 1/8 in thick, cut to length gunwale to gunwale over the ribbands. Space them 3 in apart on centres along the keelson, one over each mold. Fasten each rib to the outside of the keelson with two 5/8 in copper clout nails, spring it in under the ribbands and fasten it to the gunwales. Then remove the ribbands.
यस चरणका सामग्री:
सिडरको फल्याक2 टुक्रा
तामाका चौडा टाउके किला1 टुक्राचाहिने औजार:
हाते आरा
घन
नाप्ने फित्ता8
8
Plank the hull
Plank the hull
Plank with 1/8 in cedar, bent cold, full length stem to stem, butted edge to edge without bevel, about 3 in wide; begin with the garboard strake at the keel and end with the sheer strake level with the gunwale. Punch nail holes with an awl, staggered along the ribs; clamp the plank, drive copper clout nails and clinch them inside on a clinch iron. Trim the plank ends to the stems and gunwales, saw the backbone in two to take out the frame, tack strips across the gunwales against sagging, and nail where the molds were.
यस चरणका सामग्री:
सिडरको फल्याक4 टुक्रा
तामाका चौडा टाउके किला1 टुक्रा
तामाका साना किला (ट्याक)1 टुक्राचाहिने औजार:
आर (छेड्ने सियो)
सी-आकारको क्ल्याम्प
किला मोड्ने फलाम
घन
हाते आरा9
9
Fit risings, seats, decks and thwarts
Fit risings, seats, decks and thwarts
Nail 1/2 in square oak or ash seat risings, 14 ft long, about 4 in below the gunwale, boring first and clinching inside. Make the seat frames as Fig. 10 and cane them or tack on canvas (a kneeling paddler may use a 4 or 5 in seat bar instead). Notch the 8 x 1-1/8 x 3/8 in deck beams to wedge about 1/2 in against the gunwales (Fig. 11) and fix each with a 1-1/4 in No. 10 screw through the gunwale. Shape the decks 16 x 8 in (Fig. 12) and fix them with three 1-1/4 in No. 10 screws into the beam and three along each gunwale. Screw a centre thwart of oak or ash, 3/8 in thick, 2 in tapering to 1 in, under the gunwales amidships; extra thwarts behind the forward seat and about 3 ft forward of the rear seat stiffen it.
यस चरणका सामग्री:
सेतो फलाँटको फल्याक2 टुक्रा
सिडरको फल्याक1 टुक्रा
तामाका चौडा टाउके किला1 टुक्रा
पित्तलका काठ पेच30 टुक्रा
क्यानभास कपडा1 टुक्राचाहिने औजार:
हातले घुमाउने ड्रिल र बिट
पेचकिला - चेप्टो
हाते आरा
छिनाहरू
घन10
10
Lay the canvas
Lay the canvas
Lay the No. 6 canvas smoothly on the hull and trim it to fold at the stems (Fig. 13). Melt the black marine glue in a can over a moderately hot fire and spread a fairly heavy coat over one side of the canvas with a stiff brush. Lay it on and iron it with a moderately hot flatiron so the glue melts into the planking. Tack the edges along the gunwales and fold the canvas smoothly at the stems, tacking exactly down the stem centre line.
यस चरणका सामग्री:
क्यानभास कपडा1 टुक्रा
समुद्री गम1 टुक्रा
तामाका साना किला (ट्याक)1 टुक्राचाहिने औजार:
टिनको डब्बा
चौडा रङ्गाउने बुरुस
फलामे इस्त्री
कैँची
घन11
11
Fenders, stem bands and keel
Fenders, stem bands and keel
Tack 1/2 in round molding over the canvas edge (or a 1 in strip of planking with 1-1/4 in brads every 2 or 3 in). Put on stem bands of wood about 3/8 in square, rounded, with 1-1/4 in brads, or better, 3/8 in brass oval stem band with 3/4 in screws. An outside keel is optional: about 1 x 1/2 in of oak or ash tapered to the stem bands, or a flat keel about 2-1/2 in wide of 3/8 in oak or ash, which turns more easily and guards the bottom.
यस चरणका सामग्री:
आधा गोलो काठको पट्टी1 टुक्रा
डुङ्गाको अगाडिको पित्तल पट्टी2 टुक्रा
पित्तलका काठ पेच12 टुक्रा
सेतो फलाँटको फल्याक1 टुक्रा
काँटी1 टुक्राचाहिने औजार:
घन
पेचकिला - चेप्टो
रन्दा
हाते ड्रिल12
12
Paint and finish
Paint and finish
Give the canvas a coat of shellac to waterproof it, then four coats of paint to fill the fibres, rubbing down the second and third with fine sandpaper. Finish all woodwork with three coats of good outside spar varnish. A removable slatted grating of soft-pine lattice, about 1-1/8 in wide and 1-1/4 in thick as printed, screwed to curved cross strips (not the ribs), protects the bottom.
यस चरणका सामग्री:
सेलाकको वार्निस1 टुक्रा
तेलरङ1 टुक्रा
गिट्टी कागज1 टुक्रा
मस्तुलको वार्निस1 टुक्रा
सल्लाको फल्याक1 टुक्राचाहिने औजार:
चौडा रङ्गाउने बुरुस
पेचकिला - चेप्टो13
13
Troubleshooting
Troubleshooting
Canoe troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
From "How to Build a Canoe, Part I" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 77-84). As printed, his text differs in places: the backbone's lower edge is 1/2 in longer in one sentence and 1 in in the next; the list gives No. 8 deck screws, the text No. 10; the list's seat frames (30 x 3 and 12 x 2-1/4 in) differ from Fig. 10 (29 x 9 in); the fenders are half-round in the list and round in the text. The metric figures are ours.
सामग्री
16- 4 टुक्राप्लेसहोल्डर
- 6 टुक्राप्लेसहोल्डर
- 3 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 3 टुक्राप्लेसहोल्डर
- 30 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 2 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 2 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
आवश्यक उपकरणहरू
21- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- 1 vendor sell this, none ship to you yetप्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- 1 vendor sell this, none ship to you yetप्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
यो खाकाले बनाउँछ
सम्बन्धित ब्लुप्रिन्ट
यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त
CC0 सार्वजनिक डोमेन
यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।
ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।


