कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
The Hooded Fountain Paint Brush: A Dome Shares the Paint Between Both Sides
Paint fed into the middle of a brush clogs its head, and one side of the bristles runs dry.
Franklin E. Fornwalt of Harrisburg, Pennsylvania, received US 842,644, patented 29 January 1907, for a fountain brush "for applying paint": a tin holder clamped over the brush carries a reservoir whose floor has a row of apertures under a hollow turning valve, and below it a hood whose dome sends equal paint to both sides of the bristles.
This rung works out the flow a brush needs, then folds the holder from aluminium sheet over a 120 mm brush and measures the paint it lays on each side of a stroke.
मध्यम
About 5 hours
निर्देशनहरू
1
1
Paint the brush needs
Paint the brush needs
Jupyter नोटबुक लोड हुँदैछ…
2
2
A turned perforated tube before it
A turned perforated tube before it
The embedded blueprint turns a perforated tube to change how water leaves a brush. Fornwalt turns a perforated valve to open or close a row of holes over a hood.
3
3
Read US 842,644
Read US 842,644
"In virtue of the provision of the said hood D paint is effectually prevented from getting on the brush-head b, and at the same time liability of the brush becoming choked and impaired is reduced to a minimum. It will also be apparent that the hood D conveys an equal quantity of paint to each side of the body of bristles a and assures the paint reaching the sides of the body of bristles in the form of thin layers, which obviously contributes materially to the efficiency of the fountain-brush as a whole."
4
4
Fold the tank
Fold the tank
Fold aluminium sheet into a box 160 × 60 × 70 mm with a lid. Rivet the seams and seal them inside with silicone. Cut a 25 mm filling hole in the lid.
यस चरणका सामग्री:
एल्युमिनियमको पाता1 टुक्रा
पप रिभेट1 टुक्रा
सिलिकोन सिलेन्ट1 टुक्राचाहिने औजार:
पाता काट्ने कैँची
चेप्टो मुखको प्लास
बेन्चको भाइस
पप रिभेट गन किट
तारविनाको ड्रिल
ड्रिल टुप्पाको सेट
होल-स सेट
छालाका काम गर्ने पन्जा5
5
Drill the floor
Drill the floor
Drill six 3 mm holes along the floor's centre line, 20 mm apart.
चाहिने औजार:
तारविनाको ड्रिलड्रिल टुप्पाको सेट
नमेटिने मसीको मार्कर
रुलर6
6
Make the turning valve
Make the turning valve
Cut 200 mm of 10 mm copper tube. Drill six 3 mm holes in a line to match the floor's, and file a 6 mm slot along the opposite side. Pass it through both end walls just above the floor and bend one end into a crank.
यस चरणका सामग्री:
तामाको नली १० मिमि1 टुक्राचाहिने औजार:
फलाम काट्ने आरातारविनाको ड्रिलड्रिल टुप्पाको सेट
रेती (हातको रेती)बेन्चको भाइस7
7
Fold the hood
Fold the hood
Bend an aluminium strip into a ridge with 40° sides and rivet it under the floor, its peak under the holes.
यस चरणका सामग्री:
एल्युमिनियमको पाता1 टुक्रापप रिभेट1 टुक्राचाहिने औजार:
बेन्चको भाइसपप रिभेट गन किट8
8
Clamp on the brush
Clamp on the brush
Rivet two side skirts below the tank. Drill them and a 120 mm brush's stock for two M6 bolts, and clamp the brush between the skirts with nuts so their lower edges rest on the bristles.
यस चरणका सामग्री:
बुरुसको सेट1 टुक्रा
षट्कोणीय बोल्ट सङ्ग्रह1 टुक्रा
छपत्रे नट1 टुक्रा
चेप्टो वासर1 टुक्रापप रिभेट1 टुक्राचाहिने औजार:
तारविनाको ड्रिलड्रिल टुप्पाको सेट
मिलाउन मिल्ने पाना9
9
The patent drawing
The patent drawing
US 842,644 drawing sheet, public domain (expired patent).
10
10
Paint and weigh
Paint and weigh
Fill the tank with thinned acrylic paint. Weigh a plywood board, open the valve half, and paint one 1 m stroke each way. Weigh it again; compare how wet each side of the bristles is.
यस चरणका सामग्री:
एक्रिलिक रङको सेट1 टुक्रा
पानी1 टुक्रा
प्लाइउडको पाता1 टुक्राचाहिने औजार:
डिजिटल भान्साको तराजु
नाप्ने फित्ता
रोकघडी11
11
A brush that clogs, floods or paints one side
A brush that clogs, floods or paints one side
Hooded fountain paint brush troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Franklin E. Fornwalt** of Harrisburg, Pennsylvania, filed US 842,644 on 28 September 1906; it was patented 29 January 1907. His holder is preferably tin; bolts through the brush head with thumb nuts press the side walls in against the bristles, and removing them lets the brush be replaced. A connection may take a hose from a paint supply or compressed air. A right-angled form paints vertical surfaces, feeding the upper side of the bristles only.
**Honest limits.** Riveted aluminium stands in for his tin, and plain nuts for his thumb nuts. Your weights are the result.
सामग्री
11- 1 टुक्राप्लेसहोल्डर
- 3 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
- 1 टुक्राप्लेसहोल्डर
आवश्यक उपकरणहरू
16- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- 1 vendor sell this, none ship to you yetप्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- प्लेसहोल्डर
- 1 vendor sell this, none ship to you yetप्लेसहोल्डर
- प्लेसहोल्डर
सम्बन्धित ब्लुप्रिन्ट
यी ब्लुप्रिन्टहरूले ज्ञान साझा गर्छन् — प्रविधि, सामग्री वा सिद्धान्त
The Tube-in-the-Back Fountain Brush: Turn the Tube and the Jets Become a Soak
YourGrandma द्वारा
यान्त्रिकी
१७
०
०
०
०
०
Making Hide Glue Distemper — The Traditional Ceiling and Wall Paint of Europe
Charlie द्वारा
कला
६७
०
०
०
४
०
The Long-Handled Fountain Brush: A Ring of Holes Wets the Bristles From the Ground
Martin द्वारा
यान्त्रिकी
७
०
०
०
०
०
CC0 सार्वजनिक डोमेन
यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।
ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।