सहयोग
कला
सुन्दरता र कल्याण
हस्तकला
संस्कृति र इतिहास
मनोरञ्जन
वातावरण
खाना र पेय
रिभर्स इन्जिनियरिङ
विज्ञान
खेलकुद
प्रविधि
पहिर्न मिल्ने
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
Woody

सिर्जनाकर्ता

Woody

4. नोभेम्बर 2026NO
१२
०
०
०
०

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)

A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle. Painted red inside and light green outside, lined in a lighter colour and black. Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
मध्यम
Unknown

निर्देशनहरू

1

Make the hales

Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.

यस चरणका सामग्री:

एशको फल्याकएशको फल्याक1 hales 3 ft 1 in x 1 5/8 x 1 1/2 in

चाहिने औजार:

हाते आराहाते आरा
रन्दारन्दा
दुई बिँडको रन्दादुई बिँडको रन्दा
2

Frame with oak cross-pieces

Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.

यस चरणका सामग्री:

सेतो फलाँटको फल्याकसेतो फलाँटको फल्याक1 टुक्रा
काठको किल्लाकाठको किल्ला1 3/16 in pins

चाहिने औजार:

पिठ्युँ भएको आरापिठ्युँ भएको आरा
चुलको छिनोचुलको छिनो
चिन्ह लगाउने गेजचिन्ह लगाउने गेज
हातले घुमाउने ड्रिल र बिटहातले घुमाउने ड्रिल र बिट
मिलाउन मिल्ने कोणमापकमिलाउन मिल्ने कोणमापक
3

Fit the legs and stays

Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.

यस चरणका सामग्री:

सेतो फलाँटको फल्याकसेतो फलाँटको फल्याक1 legs 1 1/2 in square, stays
गोलो टाउको भएको बोल्टगोलो टाउको भएको बोल्ट4 3 in

चाहिने औजार:

हाते आराहाते आरा
हातले घुमाउने ड्रिल र बिटहातले घुमाउने ड्रिल र बिट
स्क्रुड्राइभर सेटस्क्रुड्राइभर सेट
4

Bottom and sides

Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.

यस चरणका सामग्री:

सल्लाको फल्याकसल्लाको फल्याक1 1/2 in bottom, 5/8 in sides
तेलरङतेलरङ1 टुक्रा

चाहिने औजार:

हाते आराहाते आरा
रन्दारन्दा
बुरुसको सेटबुरुसको सेट
5

Front board and ironwork

Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.

यस चरणका सामग्री:

सल्लाको फल्याकसल्लाको फल्याक1 3/4 in front board
फलामका काँटीफलामका काँटी1 1 1/2 in cut nails
नरम इस्पातको चेप्टो पाटोनरम इस्पातको चेप्टो पाटो1 7/8 in hoop iron
काठका पेचकाठका पेच1 3/4 in round-headed
तेलरङतेलरङ1 टुक्रा

चाहिने औजार:

हाते आराहाते आरा
घनघन
स्क्रुड्राइभर सेटस्क्रुड्राइभर सेट
बुरुसको सेटबुरुसको सेट
6

Make the wheel

Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.

यस चरणका सामग्री:

एशको फल्याकएशको फल्याक1 axle and felloes
सेतो फलाँटको फल्याकसेतो फलाँटको फल्याक1 spokes
फलामको गोलो डण्डीफलामको गोलो डण्डी1 3/8 in pins
काठको किल्लाकाठको किल्ला4 1/4 in
नरम इस्पातको चेप्टो पाटोनरम इस्पातको चेप्टो पाटो1 3/4 x 1/8 in tyre

चाहिने औजार:

काठको खरादकाठको खराद
दुई बिँडको रन्दादुई बिँडको रन्दा
हातले घुमाउने ड्रिल र बिटहातले घुमाउने ड्रिल र बिट
घनघन
7

Hang the wheel and paint

Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.

यस चरणका सामग्री:

नरम इस्पातको चेप्टो पाटोनरम इस्पातको चेप्टो पाटो2 3/4 x 1/8 in irons
काठका पेचकाठका पेच1 टुक्रा
तेलरङतेलरङ1 टुक्रा

चाहिने औजार:

स्क्रुड्राइभर सेटस्क्रुड्राइभर सेट
बुरुसको सेटबुरुसको सेट

सामग्री

10

आवश्यक उपकरणहरू

12

CC0 सार्वजनिक डोमेन

यो ब्लुप्रिन्ट CC0 अन्तर्गत जारी गरिएको छ। तपाईं अनुमति नसोधी प्रतिलिपि, परिमार्जन, वितरण र प्रयोग गर्न सक्नुहुन्छ।

ब्लुप्रिन्ट मार्फत उत्पादनहरू किनेर सिर्जनाकर्तालाई सहयोग गर्नुहोस् सिर्जनाकर्ता कमिसन विक्रेताले तोकेको, वा यो ब्लुप्रिन्टको नयाँ संस्करण बनाउनुहोस् र आम्दानी बाँड्न आफ्नो ब्लुप्रिन्टमा जडानको रूपमा समावेश गर्नुहोस्।

छलफल

(0)

लग इन छलफलमा सामेल हुन

टिप्पणीहरू लोड गर्दै...