SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Condenser Worm: Copper Tube Coiled in a Water Tub
Forge

Nilikha ni

Forge

14. Oktubre 2026NO
16
0
0
0
0

Condenser Worm: Copper Tube Coiled in a Water Tub

A still's vapour becomes liquid again in the worm: a copper tube coiled in a tub of cold water. Ure (1839) describes copper stills with a capital and worm, and retorts piped to a worm-tub. Fill copper tube with dry sand so it bends without kinking, wind it round a wooden drum with a steady fall, and set it in a tub with the outlet through the side near the bottom. The picture: our diagram, the worm in its tub, vapour in at the top and liquid out at the bottom.
Katamtaman
A day

Mga Tagubilin

1

Fill the tube

Cork one end of the copper tube, fill it with dry sand tamped down, and cork the other end.

Mga materyales para sa hakbang na ito:

Tubong tansoTubong tanso8 m
BuhanginBuhangin2 kg
Mga tapon na kortsaMga tapon na kortsa2 piraso

Mga kailangang kasangkapan:

Kahoy na PamukpokKahoy na Pamukpok
2

Wind the coil

Saw a log into a drum about 30 cm across (our size). Anneal the tube in the fire if it is stiff, then wind it slowly round the drum, letting each turn fall about 5 cm, so the liquid always runs downhill.

Mga materyales para sa hakbang na ito:

Mga troso ng matigas na kahoy (roble, mapel, beech)Mga troso ng matigas na kahoy (roble, mapel, beech)1 piraso

Mga kailangang kasangkapan:

Lagaring PangkamayLagaring Pangkamay
Pandayan ng pandayPandayan ng panday
Guwantes na Matibay sa InitGuwantes na Matibay sa Init
3

Empty the sand

Slide the coil off the drum, pull the corks and shake and wash out all the sand.

Mga materyales para sa hakbang na ito:

TubigTubig5 litro

Mga kailangang kasangkapan:

BaldeBalde
4

Set it in the tub

Drill the tub near its bottom for the outlet, pass the lower end out through it and seal the hole with a cork and tallow. Fill the tub with cold water; renew the water as it warms.

Mga materyales para sa hakbang na ito:

Mga tapon na kortsaMga tapon na kortsa1 piraso
Taba ng Hayop (Sebo)Taba ng Hayop (Sebo)0.05 kg
TubigTubig100 litro

Mga kailangang kasangkapan:

Malaking batyang kahoyMalaking batyang kahoy
Barenang de-kamayBarenang de-kamay
5

Tube for the coil

Naglo-load ng Jupyter notebook…

Mga Materyales

6

Mga Kinakailangang Kasangkapan

7

Ang blueprint na ito ay gumagawa ng

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...