Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Disc Pressing Die: Hardened Steel, the Bore Lapped Along the Stroke (Schumacher & Souden, 1944)
The die in which powder is pressed into a flat disc: a block of hardened steel with a round bore, and close-fitting plungers that press the powder in it. The bore is lapped with rouge along the stroke, so its last fine scratches run the way the disc comes out.
Result: a die for pressing metal or ceramic powders into discs, at 5 to over 100 tons per square inch.
Source: E. E. Schumacher and A. G. Souden, Some Aspects of Powder Metallurgy, Bell System Technical Journal 23 (1944), pp. 431-433 and 454-455. Unknown: the steel, the hardening, sizes and clearances. Picture drawn by Youblob.
Abantado
Unknown
Mga Tagubilin
1
1
Make the die and plungers
Make the die and plungers
Make the die of steel with a round bore through it, and plungers that fit the bore closely; there must be some clearance between them. Make the bore about three times as deep as the disc will be thick. Light, fluffy powders need a deeper die and longer plungers. Ours: tool steel for the die, and a lathe to bore and turn. Not given: the steel, sizes, clearance, the plungers' metal.
Mga materyales para sa hakbang na ito:
Parisukat na barang tool steel1 die
Hindi alam na metal1 plungersMga kailangang kasangkapan:
Torno para sa Metal
Hindi alam na sukat2
2
Harden the die
Harden the die
Harden the die. For very abrasive powders, make the die of hard carbide or line it with carbide instead. Ours: a heat-treating oven and a quench. Not given: the hardening heat and quench.
Mga kailangang kasangkapan:
Hurno para sa heat treatment
Timbang pampatigas3
3
Lap the bore along the stroke
Lap the bore along the stroke
Polish the bore to a high finish by lapping with polishing rouge, moving the lap in the direction of the plunger stroke. The fine scratches that remain then run the way the pressed disc is pushed out, not across it.
Mga kailangang kasangkapan:
Pulang pampakintab ng platero4
4
Press a disc
Press a disc
Fill the bore with powder and press it with the plungers in a mechanical or hydraulic press, at 5 to over 100 tons per square inch. The powder hardly flows sideways, and friction at the die wall makes the pressure uneven: a part that is long for its width may come out with a soft, less dense middle. Push the disc out along the bore.
Mga kailangang kasangkapan:
Haydroliko na pandiinMga Materyales
2- Placeholder
- 1 plungersPlaceholder
Mga Kinakailangang Kasangkapan
6- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Mga Materyales ng Nakakonektang Blueprint
10% Atribusyon
Tool-Steel Bar: Crucible Steel Drawn Out at a Cherry-Red Heat
ni Forge
Panday
31
0
0
0
5
0
10% Atribusyon
Jewellers' Rouge Precipitated from Copperas, Ure 1839
ni Charlie
Inorganiko
12
0
0
0
1
0
10% Atribusyon
Hydraulic Press
ni Emma
Paggawa ng Metal
53
0
0
0
10
0
10% Atribusyon
Building a Screw-Cutting Lathe — The Machine That Makes Other Machines
ni Gimli
Paggawa ng Metal
57
0
0
0
4
0
Ang blueprint na ito ay gumagawa ng
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.