Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)
Penny

Nilikha ni

Penny

2. Nobyembre 2026DK
6
0
0
0
0

Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)

The equal-arm balance with its weights replaced by electricity. The pan sits on a coil in the gap of a permanent magnet. A load pushes it down; capacitor rings sense the smallest movement, and a servo drives just enough current through the coil to lift it back to its rest position. That current is the weight. Result: a balance that reads the weight in grams or ounces on a digital display, with no weights to handle, and tare by its circuit. Source: C. B. Akers and others (Arbor Laboratories), US Patent 4,034,819 (1977). Unknown: the resolution, capacity, magnet type, materials and sizes; the circuits are given as blocks only. Picture: patent drawing.
Abantado
2 weeks

Mga Tagubilin

1

Build the magnet circuit

Stack permanent magnets into a column with a soft iron core. Enclose them in an annular outer housing with end caps, shaped so the field crosses a narrow annular air gap at a constriction. Keep the whole structure symmetrical about its vertical axis. Mount it on a support plate fixed to an upright, such as a housing panel on a base. Not given: the magnet type, materials and sizes.

Mga materyales para sa hakbang na ito:

Maliit na MagnetMaliit na Magnet1 column
Bilog na baras na bakalBilog na baras na bakal1 soft iron core
Hindi alam na metalHindi alam na metal1 housing and end caps
Hindi kilalang materyalHindi kilalang materyal1 support plate, panel, base

Mga kailangang kasangkapan:

Set ng mga distornilyadorSet ng mga distornilyador
Hindi alam na sukatHindi alam na sukat
2

Hang the coil in the gap

Wind the coil tightly round the middle of a light bobbin that surrounds the core, the coil sitting in the air gap. Tabs at both ends of the bobbin pass out through holes in the end caps to suspension frames. Hang the frames from thin springy cantilevers fixed to the upright, so the bobbin can only move a short way straight up and down. Keep the bobbin and its suspension as light as possible. Put the weighing pan on top. Ours: enamelled wire.

Mga materyales para sa hakbang na ito:

Kawad na Tanso na May EnamelKawad na Tanso na May Enamel1 coil
Hindi kilalang materyalHindi kilalang materyal1 bobbin, frames, cantilevers
Pinggan ng TimbanganPinggan ng Timbangan1 piraso

Mga kailangang kasangkapan:

Hindi alam na sukatHindi alam na sukat
3

Fit the capacitor rings

Mount four capacitor rings inside the outer housing, two above and two below the air gap, facing matching rings on the bobbin. Cross-connect them so a tilt of the bobbin cancels out and only up-and-down movement shows. Connect them to a signal generator: as the bobbin moves, one set's capacitance rises and the other's falls, and the difference becomes the control voltage.

Mga materyales para sa hakbang na ito:

Hindi alam na metalHindi alam na metal1 rings
Integrated circuit (IC)Integrated circuit (IC)1 sensing circuit
Kawad na pandugtongKawad na pandugtong1 piraso
Kawad na PanghinangKawad na Panghinang1 a little

Mga kailangang kasangkapan:

PanghinangPanghinang
4

Close the servo loop and read the current

Feed the control voltage to a d.c. servo that drives current through the coil, through a flexible lead, until the bobbin is back at its rest position. Pass that current through a large stable resistor, a thermal resistor that corrects for temperature and a calibration potentiometer: the voltage across them stands for the weight. A separate circuit (comparators, saw-tooth generator, oscillator and counter) turns it into a count read out as grams or ounces. Tare is ordinary circuit logic. Ours: a segment LCD; check with calibration weights.

Mga materyales para sa hakbang na ito:

Integrated circuit (IC)Integrated circuit (IC)1 servo and counting circuits
ResistensyaResistensya2 stable resistor, thermal resistor
PotensiyometroPotensiyometro1 calibration
Segment LCD panelSegment LCD panel1 display
Kawad na PanghinangKawad na Panghinang1 a little

Mga kailangang kasangkapan:

PanghinangPanghinang
Set ng timbang na pangkalibrasyonSet ng timbang na pangkalibrasyon

Mga Materyales

12

Mga Kinakailangang Kasangkapan

4

Kaugnay na Blueprint

Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...