Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Nilikha ni

Forge

13. Nobyembre 2026NO
6
0
0
0
0

Hind Horseshoe: Round-Pointed Toe, No Seating, Nail Holes in the Front Two-Thirds (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat hind horseshoe from Lungwitz and Adams, A Text-Book of Horseshoeing (1913). It is made "in like manner" as the front shoe, but the branches are bent to a different curve, giving a round-pointed toe, the hoof side is not concaved, and the nail holes run further back. Fitting and nailing the shoe to the horse, calks and clips are not covered here.
Katamtaman
8-15 minutes a pair, once practised

Mga Tagubilin

1

Bar length and sizes

Naglo-load ng Jupyter notebook…
2

Read Lungwitz and Adams

"The hind shoe is made in like manner, but the branches are not bent in a circle but given that form shown in Fig. 106."
3

Measure and cut the bar

Measure the hoof from the point of the toe to the buttress and its greatest width; add them for the bar length. Trace the outline on stiff paper if you want to keep it. Cut the bar.

Mga materyales para sa hakbang na ito:

Baras na pandayang bakalBaras na pandayang bakal1 piraso

Mga kailangang kasangkapan:

Panukat na TapePanukat na Tape
LapisLapis
Makakapal na sheet ng papelMakakapal na sheet ng papel
Pandayan ng pandayPandayan ng panday
Pait na pamutol sa palihanPait na pamutol sa palihan
Sipit ng PandaySipit ng Panday
4

Bend the outer branch to the hind curve

Heat the bar white-hot just beyond its middle and bend it over the sledge head on the anvil face with the turning hammer, as for the front shoe, but bend the branch to the flatter, angled curve of his Fig. 106, not to a circle. The outer branch is made first, the right shoe first in a pair. Draw out the end with the sledge.

Mga kailangang kasangkapan:

Pandayan ng pandayPandayan ng panday
Palihang may tukaPalihang may tuka
ParagosParagos
Martilyong pambilogMartilyong pambilog
Sipit ng PandaySipit ng Panday
5

Bevel, flatten and shape

Bevel the branch on the horn, then flatten it. Bending the toe of a hind shoe backs up the inner edge and thins the outer, so hammer the shoe smooth and even. Shape it so the toe is round-pointed, "yet not too much so", as in his Fig. 116.

Mga kailangang kasangkapan:

Palihang may tukaPalihang may tuka
Martilyong pambilogMartilyong pambilog
Sipit ng PandaySipit ng Panday
6

Round the inner edge and fuller

Concaving is not necessary: just round the inner edge of the web. Fuller the ground side as for the front shoe, to about two-thirds of the thickness.

Mga kailangang kasangkapan:

Palihang may tukaPalihang may tuka
Fuller (bakal na panguka)Fuller (bakal na panguka)
ParagosParagos
Martilyong pambilogMartilyong pambilog
Sipit ng PandaySipit ng Panday
7

Stamp the nail holes

Stamp and pritchel the nail holes in the front two-thirds of the shoe, none at the toe: usually one more than a front shoe, seldom more than eight. Set each as far from the outer edge as the wall is thick; on a hind hoof the wall is nearly as thick at the quarters as at the toe.

Mga kailangang kasangkapan:

Palihang may tukaPalihang may tuka
Mainit na pambutasMainit na pambutas
Pambutas ng bakal ng kabayoPambutas ng bakal ng kabayo
Martilyong pambilogMartilyong pambilog
Sipit ng PandaySipit ng Panday
8

Make the second branch and finish

Make the inner branch the same way, turned to the left. Go over the outer edge on the horn and hammer the bearing surface smooth and level. Rough it out in two heats if you can.

Mga kailangang kasangkapan:

Pandayan ng pandayPandayan ng panday
Palihang may tukaPalihang may tuka
Martilyong pambilogMartilyong pambilog
Fuller (bakal na panguka)Fuller (bakal na panguka)
Mainit na pambutasMainit na pambutas
Pambutas ng bakal ng kabayoPambutas ng bakal ng kabayo
Sipit ng PandaySipit ng Panday
9

Troubleshooting

Hind shoe troubleshooting.

Flow

Loading...
10

History and honest limits

From **A Text-Book of Horseshoeing**, by A. Lungwitz and John W. Adams, 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F. His Fig. 116 shows a hind shoe with toe- and heel-calks; the calks and the toe-clip are not made here, as this chapter gives no method for forging heel-calks or drawing clips. Fitting and nailing are not covered. The metric figures are ours.

Mga Materyales

1

Mga Kinakailangang Kasangkapan

12

Ang blueprint na ito ay gumagawa ng

CC0 Pampublikong Domain

Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.

Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.

Talakayan

(0)

Mag-login upang sumali sa talakayan

Naglo-load ng mga komento...