SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Riven Hardwood Dowels with a Dowel Plate
A dowel split along the grain keeps every fibre running its full length, so it is stronger than one sawn across the grain. Split a straight log into sticks, dry them, rough them to eight sides and drive each through the holes of a steel dowel plate with a mallet: the sharp edge of each hole shaves the stick round.
Dry dowels matter: wood shrinks as it dries, and a dry dowel takes up moisture from the glue and swells tight.
Baguhan
2 hours, plus drying
Mga Tagubilin
1
1
Cut a billet
Cut a billet
Saw a 300 mm length from a straight, knot-free hardwood log such as oak, ash or hickory.
Mga materyales para sa hakbang na ito:
Mga troso ng matigas na kahoy (roble, mapel, beech)1 pirasoMga kailangang kasangkapan:
Lagaring pantabas
Panukat na Tape2
2
Riving, step by step
Riving, step by step
How to split along the grain with a froe and mallet.
3
3
Rive the sticks
Rive the sticks
Split the billet in halves, then halves again with the froe and mallet, until each stick is about 5 mm wider than the dowel you want.
Mga kailangang kasangkapan:
Froe (panghating kutsilyo)
Kahoy na Pamukpok4
4
Dry them
Dry them
Leave the sticks indoors, spaced apart, for several weeks. They are ready when the moisture meter reads 6–8 %, or a little drier than the wood they will go into.
Mga kailangang kasangkapan:
Panukat ng halumigmig ng kahoy na may karayom5
5
Rough to eight sides
Rough to eight sides
Plane or pare each stick square, then take the corners off to eight sides, about 1 mm larger than the dowel. Chamfer one end to a blunt point.
Mga kailangang kasangkapan:
Block plane
Set ng pait para sa kahoy6
6
Drive through the plate
Drive through the plate
Clamp the dowel plate in the vise over a gap so the dowel can drop through. Start the chamfered end in the hole one size larger than you want and drive it through with the mallet; then the final hole.
Mga kailangang kasangkapan:
Plaka para sa Tarugo
Bais sa Mesang PanggawaKahoy na Pamukpok
Salaming pangkaligtasan7
7
Check and cut
Check and cut
Measure the dowel with the caliper along its length. Saw to length and chamfer both ends.
Mga kailangang kasangkapan:
Digital na Kalibrador 6 PulgadaLagaring pantabas8
8
Keep them dry
Keep them dry
Store the dowels in a jar with a lid until you use them, so they stay dry.
Mga kailangang kasangkapan:
Garapong Salamin na May Takip9
9
Troubleshooting
Troubleshooting
Dowel plate troubleshooting.
Flow
Loading...
Mga Materyales
1- Placeholder
Mga Kinakailangang Kasangkapan
12- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.