Pakikipagtulungan
SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Teapot: a Tinplate Picnic Teapot with Cock and Strainer (Hasluck, 1907)
A square tinplate teapot from a picnic outfit: folded from one blank, with a hinged lid, and a cock at the bottom behind a perforated strainer that holds back the leaves.
Blank 1 ft 4 1/4 in by 1 ft 0 3/8 in; lid 4 1/8 by 4 in.
Source: Paul N. Hasluck, Tinplate Work (1907), pp. 37-39. Unknown: folding order, solder, the cock. Picture: Figs. 96-97 of the book.
Katamtaman
Unknown
Mga Tagubilin
1
1
Cut the body blank
Cut the body blank
Cut a piece of tin 1 ft 4 1/4 in long by 1 ft 0 3/8 in wide and mark the pattern of Fig. 96 on it, with the hole for the cock tube. Not given: the folding order. Ours: bend it up on the dotted lines and solder the seams.
Mga materyales para sa hakbang na ito:
Plantsa ng lata1 body
Panghinang na lata-tingga1 pirasoMga kailangang kasangkapan:
Panggurlis
Gunting na pangyero
Tulos
Kahoy na Pamukpok
De-kuryenteng Kautin
Flux2
2
Fit the cock and strainer
Fit the cock and strainer
Solder a tube about 1/2 in long into the hole for the cock (Fig. 97) and fit the cock to it. Develop the strainer (Fig. 98): top curve radius 1 13/16 in, chord corner to corner 2 15/16 in. Perforate it and solder it across the corner in front of the tube (Fig. 99).
Mga materyales para sa hakbang na ito:
Tubong tanso-dilaw1 1/2 in
Gripo ng pagpapatulo1 pirasoPlantsa ng lata1 strainerPanghinang na lata-tingga1 pirasoMga kailangang kasangkapan:
Kompas na dalawang tulisGunting na pangyero
Pambutas ng metal na plantsa
Tipak ng Matigas na KahoyDe-kuryenteng KautinFlux3
3
Make the hinged lid
Make the hinged lid
Cut the lid (Fig. 100) 4 1/8 by 4 in; the inner rectangle 3 1/2 by 3 1/2 in leaves 1/4 in to bend up. Cut hinge projections 1/2 in wide by 5/8 in deep with equal spaces, the outer ones only 1/4 in wide. Bend them round a wire 1/16 in thick. Hasluck adds that the teapot may be enamelled dark green.
Mga materyales para sa hakbang na ito:
Plantsa ng lata1 lid
Alambreng bakal1 1/16 inMga kailangang kasangkapan:
Gunting na pangyeroTulosKahoy na PamukpokMga Materyales
5- 1 lidPlaceholder
- 2 pirasoPlaceholder
- 1 1/2 inPlaceholder
- 1 pirasoPlaceholder
- 1 1/16 inPlaceholder
Mga Kinakailangang Kasangkapan
9- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Mga Materyales ng Nakakonektang Blueprint
Ang blueprint na ito ay gumagawa ng
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.