SINING
BEAUTY AT WELLNESS
CRAFTS
KULTURA AT KASAYSAYAN
LIBANGAN
KAPALIGIRAN
PAGKAIN AT INUMIN
REVERSE ENGINEERING
AGHAM
ISPORTS
TEKNOLOHIYA
MGA WEARABLE
Tuyere Iron: a Slotted Grate Cast in Grey Iron
The tuyere is the opening in the bottom of the forge fire through which the blast is blown. Bacon (1919): its openings must let the blast through easily while keeping cinders from dropping into the blast pipe, and there should be a way to open the pipe below and clear out the cinders that still get through. This one is a slotted grate over a socket for the blast pipe, cast in grey iron. The design and sizes are ours.
The picture: our drawing.
Abantado
2 days
Mga Tagubilin
1
1
Make the pattern
Make the pattern
From pine, make a pattern of a square plate about 15 cm across and 2 cm thick with four or five narrow slots, and a short round socket under its centre to take the blast pipe. Taper every side slightly so it draws from the sand.
Mga kailangang kasangkapan:
Tablang pino
Lagaring Pangkurba
Set ng pait para sa kahoy
Pandikit sa Kahoy
Digital na Kalibrador 6 Pulgada2
2
Ram the mould
Ram the mould
Ram the pattern up in casting sand in the flask, draw it out, and cut a sprue and a runner to the cavity.
Mga kailangang kasangkapan:
Buhangin sa paghuhulma
Kahon ng paghuhulma
Maliit na pala sa hardin3
3
Melt the iron
Melt the iron
Melting pig iron in the cupola and tapping it into the ladle.
4
4
Pour
Pour
Pour the molten grey iron from the ladle into the sprue in one steady stream until the mould is full; about 4 kg with the sprue (our estimate). Let it cool in the sand.
Mga materyales para sa hakbang na ito:
Mga tinunaw na bakal na hilaw4 kgMga kailangang kasangkapan:
Sandok ng pagbububo ng metalKahon ng paghuhulma
Mga guwantes sa paghihinang
Delantal na Katad
Panangga sa Mukha5
5
Clean up
Clean up
Shake out the casting, cut off the sprue, grind the fins and brush off the sand. Check that every slot is clear.
Mga kailangang kasangkapan:
Panggiling na pangsulok
Set ng brotsang kawadMga guwantes sa paghihinangPanangga sa Mukha6
6
Set it in the forge
Set it in the forge
Set it in the hearth with the blast pipe in its socket and a way to open the pipe below for clearing cinders. Richardson's forge had its tuyere iron four inches below the hearth surface.
Mga kailangang kasangkapan:
Digital na Kalibrador 6 PulgadaMga Materyales
1- Placeholder
Mga Kinakailangang Kasangkapan
14- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
Ang blueprint na ito ay gumagawa ng
Kaugnay na Blueprint
Ang mga blueprint na ito ay nagbabahagi ng kaalaman — mga teknik, materyales, o prinsipyo
CC0 Pampublikong Domain
Ang blueprint na ito ay inilabas sa ilalim ng CC0. Malaya kang kumopya, magbago, mamahagi, at gumamit nang walang pahintulot.
Suportahan ang Maker sa pamamagitan ng pagbili ng mga produkto sa kanilang Blueprint Komisyon ng Maker itinakda ng mga Vendor, o lumikha ng bagong bersyon ng Blueprint na ito at isama bilang koneksyon sa iyong Blueprint upang ibahagi ang kita.