دستکاری
2,115 بلوپرنٹس دستیاب • 11 ذیلی زمرے
ذیلی زمرے براؤز کریں
بلوپرنٹس (2,115)

Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)
Forge کی طرف سے
لکڑی کا کام

Long-Pilot High-Speed Wood Bits: A Flat Plate and a Long Square-Edged Pilot, No Screw Feed (Smith, 1951)
Forge کی طرف سے
دھات کاری

Angled-Side Spade Bits: Each Wing Bent Forwards Along a Diagonal Line, the Way the Bit Turns (Vasudeva, 2005)
Forge کی طرف سے
دھات کاری

Fluted-Shoulder Spade Bits With Spurs: Flutes Along the Shoulders, Stopped by Corner Spurs (Williams & Thackston, 1987)
Forge کی طرف سے
دھات کاری

Diamond-Point Spade Bits: A Thinned, Wide-Angled Point Does More of the Cutting (Southall, 1975)
Forge کی طرف سے
دھات کاری

Fluted-Point Spade Bits: A Groove Down Each Face of the Point Sharpens Its Cutting Edge (Robinson, 1957)
Forge کی طرف سے
دھات کاری

Built-Up Shaft Collar: Two Washers Welded to Four Nuts, a Set Screw in One Nut, No Machining (Dalrymple, 1939)
Forge کی طرف سے
دھات کاری

Divisible Flanged Shaft Collar: Two Halves Locked by Lugs, Bolted Through the Shaft in One of Three Hole Pairs (Obey, 1916)
Forge کی طرف سے
دھات کاری

One-Screw Two-Part Shaft Collar: Hooked Ends Reach Round the Shaft So the Halves Cannot Open (Grundy, 1907)
Forge کی طرف سے
دھات کاری

Shielded Set-Screw Shaft Collar: The Screw Head Sunk in a Groove, a Sprung Brass Band Snapped Over It (Rich, 1904)
Forge کی طرف سے
دھات کاری

Shaft Collar Without a Set Screw: Split Halves With a Tapered Thread, Clamped by a Nut (Melius, 1904)
Forge کی طرف سے
دھات کاری

Crank-and-Link Double-Dasher Churn: Two Dashers' Cranks Joined by a Curved Link, One Lever Turns or Rocks Both
Buttercup کی طرف سے
خوراک اور مشروبات

Round-Bottom Square Churn: A Geared Dasher Turns in a Vessel Round Up to Its Blades and Square Above, Breakers From the Lid
Buttercup کی طرف سے
خوراک اور مشروبات

Rack-and-Pinion Opposed-Dasher Churn: Two Rows of Hanging Dashers Move Opposite Ways Through Slots in the Lid
Buttercup کی طرف سے
خوراک اور مشروبات

Shifting-Gear Grinding-Disk Churn: One Crank Wheel Is Thrown Into Gear With the Wings Below, the Grinding Disk Above, or Both
Buttercup کی طرف سے
خوراک اور مشروبات

Adjustable-Valve Dash Churn: Hinged Perforated Wings Shut Going Down, Open Coming Up, Slides Set How Big the Holes Are
Buttercup کی طرف سے
خوراک اور مشروبات

Cord-Lever Churn: A Cord Wound Round a Hollow Staff Turns It Back and Forth as a Hinged Lever Swings, a Loose Gatherer Rides Its Ribs
Buttercup کی طرف سے
خوراک اور مشروبات

Set-Wing Dasher Churn: Wings on Two Cross Rods Through the Staff Are Set by Screws to Lift or Press the Cream
Buttercup کی طرف سے
خوراک اور مشروبات

Water-and-Air Tube Churn: Two Tubes of Warm or Cold Water and an Open Air Tube Stand by the Wall, Blades Sweep Under and Between
Buttercup کی طرف سے
خوراک اور مشروبات

Bellows Rocking-Dasher Churn: A Hand Bellows Blows Air Down a Knee Nozzle Into the Cream and Rocks a Paddle Dasher Beside It
Buttercup کی طرف سے
خوراک اور مشروبات

Hinged-Arm Frame Churn: An Arm That Swings Back Holds the Dasher's Top, Its Forked Brace Holds the Cover Down
Buttercup کی طرف سے
خوراک اور مشروبات

Toothed-Disk Pass Churn: Cream Poured In Passes Once Between Fixed Toothed Disks and a Toothed Wheel Spinning Between Them
Buttercup کی طرف سے
خوراک اور مشروبات

Counter-Turning Hooped Beater Churn: One Bevel Wheel Turns a Spindle and a Hollow Shaft Opposite Ways, Spiral Hoops Sweep the Wall
Buttercup کی طرف سے
خوراک اور مشروبات

Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow
Buttercup کی طرف سے
خوراک اور مشروبات