فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
سبز مستقبل
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
Controlling a DC Motor with an L298N Driver
Ed

تخلیق کار

Ed

13. جولائی 2026FI
2
0
0
0
0

Controlling a DC Motor with an L298N Driver

An Arduino pin can't power a motor directly — it can't supply enough current, and it can't reverse the flow. An L298N H-bridge solves both: the Arduino sends low-power control signals, and the driver switches the motor's own battery to run it forwards, backwards and at any speed. This is the core building block of every wheeled robot.

درمیانہ
1-2 hours

ہدایات

1

Wire the driver, motor and battery

Push the L298N's control header into the breadboard. From the Arduino, jumper pin 8 to IN1, pin 9 to IN2, and pin 10 to ENA. Connect the DC motor's two wires to the OUT1/OUT2 screw terminals, and a 4×AA battery pack to the +12V and GND motor terminals. IMPORTANT: join all the grounds together — Arduino GND, driver GND and battery GND — or the motor won't run.

اس مرحلے کے لیے مواد:

Arduino Uno R3 SMDArduino Uno R3 SMD1 piece
Full-Bridge Motor Driver Dual - L298NFull-Bridge Motor Driver Dual - L298N1 piece
Hobby Motor - GearHobby Motor - Gear1 piece
Battery Holder - 4xAA Square TerminatedBattery Holder - 4xAA Square Terminated1 piece
Breadboard - ClassicBreadboard - Classic1 piece
Jumper Wires Premium M/M 20 AWG - 15.5 cmJumper Wires Premium M/M 20 AWG - 15.5 cm1 pack
2

Connect and open the IDE

Plug the Arduino into your computer with the USB cable, open the Arduino IDE, and select Arduino Uno and its serial port. Leave the motor battery switched off until the code is uploaded.

اس مرحلے کے لیے مواد:

SparkFun Cerberus USB Cable - 1.8 meterSparkFun Cerberus USB Cable - 1.8 meter1 piece

درکار اوزار:

Computer with Arduino IDEComputer with Arduino IDE
3

Upload the motor sketch

Paste this sketch and upload, then switch on the battery. The motor runs forward, stops, reverses, and stops — on a loop.

dc_motor_l298n.inoarduino
// Control a DC motor's speed and direction with an L298N H-bridge.
// L298N IN1 -> pin 8, IN2 -> pin 9, ENA (PWM speed) -> pin 10.
// The motor is powered by the battery pack through the driver; all grounds are joined.

const int IN1 = 8;
const int IN2 = 9;
const int ENA = 10;   // PWM speed pin (0-255)

void setup() {
  pinMode(IN1, OUTPUT);
  pinMode(IN2, OUTPUT);
  pinMode(ENA, OUTPUT);
}

void loop() {
  // forward at medium speed
  digitalWrite(IN1, HIGH);
  digitalWrite(IN2, LOW);
  analogWrite(ENA, 180);
  delay(2000);

  // stop
  analogWrite(ENA, 0);
  delay(1000);

  // reverse at full speed
  digitalWrite(IN1, LOW);
  digitalWrite(IN2, HIGH);
  analogWrite(ENA, 255);
  delay(2000);

  // stop
  analogWrite(ENA, 0);
  delay(1000);
}
4

Test and control it

Watch the motor go forward, stop, reverse. IN1/IN2 set the direction (swap which is HIGH to flip it); the number in analogWrite(ENA, ...) sets the speed from 0 (off) to 255 (full). If the motor doesn't spin, check that all three grounds are joined and the battery is on.

5

Make it a robot

The L298N drives TWO motors. Wire a second motor to OUT3/OUT4 and control it with IN3, IN4 and ENB on three more Arduino pins. Two motors on a chassis with wheels gives you a robot base you can drive — turn by running the wheels at different speeds or directions.

مواد

7

درکار اوزار

1
Estimated Total
$60.00

متعلقہ بلیو پرنٹ

یہ بلیو پرنٹ علم بانٹتے ہیں — تکنیک، مواد یا اصول

Blinking LED — Your First Arduino Projectبذریعہ Admiral OOM
Driving a Motor — SIK Circuit 12بذریعہ Ed

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Controlling a Stepper Motor with an EasyDriverelectronics
Blinking an LED with LilyPad Arduinoelectronics
Making a Motion-Reactive LilyPad Patchelectronics
Making a Color-Changing LilyPad Patchelectronics
Building a Carbon Monoxide Detectorelectronics
Building an Air-Quality Monitorelectronics

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...