فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

تخلیق کار

Penny

14. اکتوبر 2026DK
23
0
0
0
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
درمیانہ
Two to three days

ہدایات

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

اس مرحلے کے لیے مواد:

چپٹی ٹول اسٹیل کی سلاخچپٹی ٹول اسٹیل کی سلاخ1 ٹکڑا

درکار اوزار:

دھات کی ریتیدھات کی ریتی
ہاتھ کا برماہاتھ کا برما
ڈیجیٹل ورنیئر کیلیپر ۶ انچڈیجیٹل ورنیئر کیلیپر ۶ انچ
لوہار کی بھٹیلوہار کی بھٹی
آب دینے کی بالٹیآب دینے کی بالٹی
حفاظتی عینکحفاظتی عینک
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

اس مرحلے کے لیے مواد:

سخت لکڑی کی پتلی پٹیسخت لکڑی کی پتلی پٹی2 ٹکڑے
نرم فولاد کی گول سلاخنرم فولاد کی گول سلاخ0.3 m

درکار اوزار:

دھات کی ریتیدھات کی ریتی
لوہار کی بھٹیلوہار کی بھٹی
آب دینے کی بالٹیآب دینے کی بالٹی
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

اس مرحلے کے لیے مواد:

پیتل کی چادرپیتل کی چادر1 ٹکڑا
مومی کتان کا دھاگہمومی کتان کا دھاگہ3 m

درکار اوزار:

چادر کاٹنے کی قینچیچادر کاٹنے کی قینچی
ہاتھ کا برماہاتھ کا برما
دھات کی ریتیدھات کی ریتی
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

درکار اوزار:

دھات کی ریتیدھات کی ریتی
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

اس مرحلے کے لیے مواد:

پیتل کی سِلیپیتل کی سِلی2 کلوگرام
لکڑی کا کوئلہلکڑی کا کوئلہ1 as required
ڈھلائی کی ریتڈھلائی کی ریت5 کلوگرام

درکار اوزار:

لوہار کی بھٹیلوہار کی بھٹی
آگ روک مٹی کی کٹھالیآگ روک مٹی کی کٹھالی
کٹھالی کی چمٹیکٹھالی کی چمٹی
ڈھلائی کا سانچہ صندوق (اوپری اور نچلا)ڈھلائی کا سانچہ صندوق (اوپری اور نچلا)
ویلڈنگ کے دستانےویلڈنگ کے دستانے
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

اس مرحلے کے لیے مواد:

پانیپانی1 لیٹر

درکار اوزار:

درجہ بند سلنڈردرجہ بند سلنڈر
دھات کی ریتیدھات کی ریتی
7

A binary set of weights

Jupyter نوٹ بک لوڈ ہو رہی ہے…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

مواد

9

درکار اوزار

12

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...