فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
Hand Lens 10×: a Small, Steep Lens Ground and Mounted
Penny

تخلیق کار

Penny

14. اکتوبر 2026DK
20
0
0
0
0

Hand Lens 10×: a Small, Steep Lens Ground and Mounted

A 10× hand lens is a small convex lens of about 25 mm focal length: held close to the eye, its magnifying power is about a quarter of a metre divided by the focal length. Grind a small pair of discs to a steep curve as for any convex lens, then seat the convex one in a turned wooden ring with a cord to carry it. The picture: a low-power reading magnifier on a dictionary page; a 10× hand lens works the same way with a much smaller, steeper lens.
اعلیٰ
A week

ہدایات

1

Two small discs

Cut two small glass discs, about 15 mm across, from glass at least 5 mm thick (each face of the lens goes over a millimetre deep), and pitch each to a short wooden handle.

اس مرحلے کے لیے مواد:

شیشے کی چادرشیشے کی چادر1 ٹکڑا
چیڑ کے تارکول کی لئیچیڑ کے تارکول کی لئی10 گرام
سخت لکڑی کی پتلی پٹیسخت لکڑی کی پتلی پٹی1 ٹکڑا

درکار اوزار:

شیشہ کاٹنے کا آلہشیشہ کاٹنے کا آلہ
شیشہ کترنے کا پلاسشیشہ کترنے کا پلاس
حفاظتی عینکحفاظتی عینک
2

Grind to a steep curve

Grind them together with wet coarse grit, the same disc always on top, until the faces are steep enough (see the notebook). Then the second faces. The bottom disc is the lens.

اس مرحلے کے لیے مواد:

پانیپانی1 لیٹر

درکار اوزار:

ڈیجیٹل ورنیئر کیلیپر ۶ انچڈیجیٹل ورنیئر کیلیپر ۶ انچ
سیلیکون کاربائیڈ کے دانےسیلیکون کاربائیڈ کے دانے
3

Fine grind and polish

Fine grits, then polish both faces on a small pitch lap with tin oxide and water until clear.

اس مرحلے کے لیے مواد:

ٹن آکسائیڈ (اسٹینک آکسائیڈ)ٹن آکسائیڈ (اسٹینک آکسائیڈ)10 گرام
چیڑ کے تارکول کی لئیچیڑ کے تارکول کی لئی30 گرام

درکار اوزار:

سیلیکون کاربائیڈ کے دانےسیلیکون کاربائیڈ کے دانے
4

Check 10×

Focus the sun through it onto paper: the spot should be smallest about 25 mm from the lens. Grind deeper if it is longer.

درکار اوزار:

پیمانہپیمانہ
5

Turn the mount

Turn a hardwood ring on the lathe with a seat a snug fit for the lens and a small lip. Press the lens in, warm a little pitch round the back edge to hold it, drill a hole in the rim for a cord loop.

اس مرحلے کے لیے مواد:

سخت لکڑی کی پتلی پٹیسخت لکڑی کی پتلی پٹی1 ٹکڑا
چیڑ کے تارکول کی لئیچیڑ کے تارکول کی لئی2 گرام
مومی کتان کا دھاگہمومی کتان کا دھاگہ0.5 m

درکار اوزار:

لکڑی کا خرادلکڑی کا خراد
گول چھینیگول چھینی
کاٹنے کی چھینی (خراد)کاٹنے کی چھینی (خراد)
ریگ مالریگ مال
ڈیجیٹل ورنیئر کیلیپر ۶ انچڈیجیٹل ورنیئر کیلیپر ۶ انچ
6

Curve for 10×

Jupyter نوٹ بک لوڈ ہو رہی ہے…
7

Use

Hold the lens close to your eye and bring the object up until it is sharp.

مواد

6

درکار اوزار

10

متعلقہ بلیو پرنٹ

یہ بلیو پرنٹ علم بانٹتے ہیں — تکنیک، مواد یا اصول

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...