فن
خوبصورتی اور تندرستی
دستکاری
ثقافت اور تاریخ
تفریح
ماحول
خوراک اور مشروبات
ریورس انجینئرنگ
سائنسز
کھیل
ٹیکنالوجی
پہننے والے آلات
Heating and Stirring Without Bumping: Why the Flask Spat at You
Charlie

تخلیق کار

Charlie

24. ستمبر 2026DE
22
0
0
0
0

Heating and Stirring Without Bumping: Why the Flask Spat at You

A liquid heated in smooth glass can go ABOVE its boiling point without boiling, because a bubble needs somewhere to start and clean glass offers nowhere. When one finally does start, the whole superheated volume flashes into vapour at once. That is bumping, and it throws the contents out of the vessel. It is most likely in exactly the situation where it matters most: clean new glassware, a quiet liquid, somebody watching closely from above. The cure is to give bubbles somewhere to form, all the time, so that none of the liquid ever gets the chance to superheat. Boiling chips or a stirrer bar do that, and they are not optional extras.
نیا سیکھنے والا
2 hours

ہدایات

1

Boiling chips or a stirrer bar, added COLD

Add boiling chips or a magnetic stirrer bar before heating starts. Their porous surface or their motion keeps a stream of small bubbles going, and small bubbles continuously are what prevents one enormous one suddenly. Never add boiling chips to a liquid that is already hot. A superheated liquid given a nucleation site all at once does exactly what the chips were meant to prevent, and does it while your hand is over the vessel. Chips are single-use. Once cooled, their pores fill with liquid and they stop working, so a flask reheated after cooling needs fresh ones — added, again, while it is cold.

اس مرحلے کے لیے مواد:

کشید کیا ہوا پانیکشید کیا ہوا پانی1 لیٹر

درکار اوزار:

ارلن مائر فلاسکارلن مائر فلاسک
مقناطیسی ہلانے والی گرم پلیٹمقناطیسی ہلانے والی گرم پلیٹ
گرم پلیٹگرم پلیٹ
2

Heat the outside evenly, not one spot

A hot plate heats the whole base; a flame heats a coin-sized patch to a temperature far above the liquid's boiling point. That hot spot is where superheating, decomposition and cracked glass all start. A water or steam bath is better again for anything below 100 degrees: it cannot exceed the boiling point of its own water, so it physically cannot overheat the contents. Sand baths and oil baths do the same job at higher temperatures. Use borosilicate, and never heat a vessel that is cracked, chipped or scratched. Thermal stress finds the flaw, and a flask that fails while hot empties its contents across the bench.

اس مرحلے کے لیے مواد:

پانیپانی1 لیٹر

درکار اوزار:

گرم پلیٹگرم پلیٹ
بوروسلیکیٹ بیکربوروسلیکیٹ بیکر
تجربہ گاہی کلیمپ (بیورٹ/فلاسک)تجربہ گاہی کلیمپ (بیورٹ/فلاسک)
کیمیائی چھینٹوں سے بچاؤ کا چشمہکیمیائی چھینٹوں سے بچاؤ کا چشمہ
3

Stir the liquid, do not just heat it

Hot liquid rises and cold sinks, so an unstirred vessel develops a hot layer at the bottom and a cool one above. The thermometer reads one of those and the reaction experiences the other. A magnetic stirrer bar turns the whole volume over and makes the temperature you measure the temperature that is actually happening. It also keeps a suspension suspended, which matters whenever a solid is dissolving or reacting. Match the bar to the vessel. A bar too long for a round-bottom flask will not spin, and a bar that has lost its grip on the field spins wildly, chips the glass, and grinds the solid you were trying to dissolve.

اس مرحلے کے لیے مواد:

سوڈیم کلورائیڈ (نمک)سوڈیم کلورائیڈ (نمک)1 ٹکڑا
کشید کیا ہوا پانیکشید کیا ہوا پانی1 لیٹر

درکار اوزار:

مقناطیسی ہلانے والی گرم پلیٹمقناطیسی ہلانے والی گرم پلیٹ
شیشے کی ہلانے والی سلاخشیشے کی ہلانے والی سلاخ
شیشے کا بیکرشیشے کا بیکر
4

Never seal it, and never look straight down it

A heated closed vessel is a pressure vessel. Loosen every stopper, and use a watch glass resting loosely on a beaker rather than anything that seals — it keeps dust out and lets vapour go. Never point the mouth of a heated tube or flask at yourself or anyone else, and never lean over one to look in. If a vessel does bump, what comes out goes straight up. And keep the heating under control at the end: remove the heat before the last of the liquid goes, the same rule as evaporating. A dry vessel still on the plate reaches the plate's full temperature within a minute or two.

درکار اوزار:

گھڑی کا شیشہگھڑی کا شیشہ
کیمیائی چھینٹوں سے بچاؤ کا چشمہکیمیائی چھینٹوں سے بچاؤ کا چشمہ
تجربہ گاہی کلیمپ (بیورٹ/فلاسک)تجربہ گاہی کلیمپ (بیورٹ/فلاسک)
گرم پلیٹگرم پلیٹ

مواد

3

درکار اوزار

9

CC0 پبلک ڈومین

یہ بلیو پرنٹ CC0 کے تحت جاری کیا گیا ہے۔ آپ اجازت لیے بغیر اس کام کو نقل، ترمیم، تقسیم اور کسی بھی مقصد کے لیے استعمال کرنے کے لیے آزاد ہیں۔

میکر کی حمایت کریں ان کے بلیو پرنٹ کے ذریعے پروڈکٹس خرید کر جہاں وہ میکر کمیشن وینڈرز کی طرف سے مقرر، کماتے ہیں، یا اس بلیو پرنٹ کی نئی تکرار بنائیں اور آمدنی شیئر کرنے کے لیے اسے اپنے بلیو پرنٹ میں کنکشن کے طور پر شامل کریں۔

بحث

(0)

لاگ ان بحث میں شامل ہونے کے لیے

تبصرے لوڈ ہو رہے ہیں...