Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Bench Glassblowing Torch: Brass Gas Blowpipe with a Glass Air Jet (Shenstone, 1916)
A glassblower's gas blowpipe you can make yourself: a brass tube with a side tube for gas, and a glass air jet down its middle fed from a foot-blower. A fine jet gives the small pointed flame for joints, and a wider jet the big brush flame for heating large tubes. It is pegged into a wooden block on a sheet-iron-covered bench, with taps for gas and air at the bench edge.
Result: a bench blowpipe for working glass tube. Make two: one about 11 mm bore for small work, one 15 to 17 mm for large.
Source: W. A. Shenstone, The Methods of Glass-Blowing (1916), pp. 3-9. Unknown: the brazing metal and the tap type. Picture: Fig. 1 of the book.
Średniozaawansowany
Unknown
Instrukcje
1
1
Braze the gas inlet
Braze the gas inlet
Take a brass tube for the body: about 11 mm bore for the small blowpipe, 15 to 17 mm for the large one. Braze a side tube for the gas onto it 10 to 12 cm from the back end, according to the tube's size. Fix a spike to it for mounting. Ours: borax as the flux. Not given: the brazing metal.
Materiały do tego kroku:
Rura mosiężna1 body and side tube
Nieznany metal1 brazing metal and spike
Boraks w proszku1 brazing fluxPotrzebne narzędzia:
Piła do metalu
Palenisko kowalskie2
2
Fit the glass air jet
Fit the glass air jet
Fit a glass tube down the middle of the brass tube, held by a cork at the back end, its tip near the mouth. For the small pointed flame, draw the tip down to the size of a large knitting needle. For a large flame rich in air, the tip may be nearly half the bore of the brass tube. Make several air tubes of different sizes for each blowpipe.
Materiały do tego kroku:
Rurka szklana3 air jets of several sizes
Korki1 jet corkPotrzebne narzędzia:
Palnik Bunsena3
3
Set up the bench
Set up the bench
Cover the bench round the blowpipe with sheet iron. Drill several holes in a block of wood so the spike can be set at different positions. Fix two taps near the bench edge, one for gas and one for air. Connect them by flexible tubes to the supplies on one side and to the blowpipe's gas inlet and air jet on the other. Ours: mild steel sheet, rubber tubing. Not given: the tap type.
Materiały do tego kroku:
Blacha ze stali miękkiej1 bench cover
Klocek z drewna twardego1 mounting block
Nieznany zawór2 gas and air taps
Wąż gumowy1 flexible tubesPotrzebne narzędzia:
Wiertarka stołowa4
4
Light it and blow
Light it and blow
Light the gas at the mouth and work a foot-blower to drive air through the glass jet into the burning gas. Little air and a small jet give the pointed flame; plenty of gas and a strong blast give the large, non-luminous brush flame.
Potrzebne narzędzia:
MiechMateriały
9- 1 body and side tubeZastępnik
- 1 brazing metal and spikeZastępnik
- 1 brazing fluxZastępnik
- 3 air jets of several sizesZastępnik
- 1 jet corkZastępnik
- 1 bench coverZastępnik
- 1 mounting blockZastępnik
- 2 gas and air tapsZastępnik
- 1 flexible tubesZastępnik
Wymagane narzędzia
5- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Materiały z połączonych planów

10% atrybucji
Venetian Borax: Refining Tincal with Lime
autor: Charlie
Nieorganiczny
22
0
0
0
1
0

10% atrybucji
Natural Rubber Tubing, Bands and Sheet: Sulfur-Cured with Heat
autor: Mary
Chemia
16
0
0
0
2
0

10% atrybucji
Oak Boards and Blocks, Milled and Air-Dried
autor: Woody
Obróbka drewna
46
0
0
0
3
0

10% atrybucji
Building a Box Bellows — The Breath That Makes Metal Obey Fire
autor: Emma
Obróbka drewna
109
0
0
0
8
0
Według tego planu powstaje
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.
