Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)
Forge

Autor

Forge

15. listopad 2026NO
6
0
0
0
0

Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)

Eli Whitney Blake's jaw breaker (patented 1858), the standard first crusher of the ore mill, as Robert Richards described it: a ribbed cast frame on four legs, a fixed jaw bedded in zinc, a steel swing jaw hung from a shaft at the top, and an eccentric that lifts a pitman to straighten two toggles and push the jaw shut; rubber springs pull it back. A wedge sets the gap; a heavy flywheel carries it through each half-turn of crushing.
Zaawansowany
Weeks (castings and machining)

Instrukcje

1

Sizes and power

Wczytywanie notatnika Jupyter…
2

Read Richards

"As the eccentric lifts the pitman, it straightens out the toggles, lengthening the distance between their outer ends. This forces the swing jaw to approach the fixed jaw, crushing the rock."
3

Frame and fixed jaw

Cast the frame of strong, ribbed cast iron or cast steel, with four legs bolted down, bearing boxes on top for the swing-jaw shaft and the eccentric shaft, and a horizontal web at the rear for the toggle block and wedge. Bed the fixed jaw against the frame end with 1/4 in. (6 mm) of zinc, and hold its jaw plate with two wedge-shaped cheek plates driven into recesses in the frame.

Materiały do tego kroku:

Odlewy żeliwneOdlewy żeliwne1 sztuka
Wlewek cynkuWlewek cynku1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych1 sztuka

Potrzebne narzędzia:

Kadź odlewniczaKadź odlewnicza
WielokrążekWielokrążek
MłotekMłotek
4

Swing jaw

Make the swing jaw of steel, fixed to its shaft by a gib and key bolt, with its jaw plate held by dovetails, a steel toggle bearing at the back and an eye near the bottom for the spring rod. Jaw plates: chilled cast iron with lengthwise 90° corrugations.

Materiały do tego kroku:

Odlewy żeliwneOdlewy żeliwne1 sztuka
Wał stalowyWał stalowy1 sztuka

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
Zestaw kluczy płaskichZestaw kluczy płaskich
5

Pitman, toggles and wedge

Hang a strong steel pitman from the eccentric shaft on babbitt bearings taken up by a key. Fit two toggles: one between the toggle block and the pitman, one between the pitman and the swing jaw, all four toggle bearings steel, held by set screws. Set the toggle block on its bolt against the wedge, which an adjusting bolt raises or lowers.

Materiały do tego kroku:

Wał stalowyWał stalowy1 sztuka
Nieznany metalNieznany metal1 sztuka
Odlewy żeliwneOdlewy żeliwne1 sztuka

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
Zestaw kluczy płaskichZestaw kluczy płaskich
6

Springs, flywheel and drive

Fit two spring rods from the swing jaw through rubber springs held in compression against a spring bar. Key a heavy flywheel to the eccentric shaft and bolt the drive pulley to it; plug all oil holes against grit and shield the boxes and toggles with the half hopper. Drive it by belt (Table 5: 275 rev./min).

Materiały do tego kroku:

Płyta z kauczuku naturalnegoPłyta z kauczuku naturalnego1 sztuka
Odlewy żeliwneOdlewy żeliwne1 sztuka
KrążekKrążek1 sztuka
Pas napędowyPas napędowy1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych1 sztuka

Potrzebne narzędzia:

Zestaw kluczy płaskichZestaw kluczy płaskich
Tokarka do metaluTokarka do metalu
7

Run and adjust

Feed rock by hand, shovel or chute into the mouth. As the jaw plates wear and the product gets coarse, raise the wedge by its nut; when that is used up, fit longer toggles that keep the pitman vertical; then turn the jaw plates end for end; last, fit new plates.

Potrzebne narzędzia:

Zestaw kluczy płaskichZestaw kluczy płaskich
8

Troubleshooting

Jaw breaker troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter II, §§ 11-14, pp. 13-17, Figs. 5-8 and Table 5 (checked on the archive.org scan oredressing01richuoft; p. 15 from its text layer). Blake's first 1858 form gave the most movement at the mouth; he soon reversed it so the bottom of the jaw moves most. Richards describes a bought Farrel or Fraser & Chalmers machine: building it from castings and metric figures are ours, and the babbitt alloy has no head yet.

Materiały

8

Wymagane narzędzia

5

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...