Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Inexpensive Bobsled: Barrel-Stave Runners, Block Knees and a Bolted Front Bob (Boy Mechanic, 1915)
H. J. Blacklidge's bobsled from The Boy Mechanic, Book 2 (1915): "any boy who can drive a nail and bore a hole can have a bobsled on short notice." Four barrel staves make the runners of two short bobs under a 4 ft board; the front bob turns on a centre bolt and is steered by a rope.
Początkujący
About 3 hours
Instrukcje
1
1
His list in centimetres
His list in centimetres
Wczytywanie notatnika Jupyter…
2
2
Read The Boy Mechanic, Book 2
Read The Boy Mechanic, Book 2
The materials: four good, solid barrel staves; four blocks 4 in long, 4 in wide and 2 in thick; two pieces 12 in long, 4 in wide and 1 in thick; one piece 12 in long, 2 in wide and 1-3/4 in thick; and a good board 4 ft long, 12 in wide and 1 in thick.
3
3
Make the two bobs
Make the two bobs
Make each crosspiece-and-knee unit from one 12 x 4 x 1 in piece and two of the blocks, as in his figure, and nail a barrel stave to each side for runners.
Materiały do tego kroku:
Klepka beczki4 sztuk
Deska sosnowa1 sztuka
Deska z drewna liściastego1 sztuka
Gwoździe1 sztukaPotrzebne narzędzia:
Piła ręczna
Młotek
Ołówek
Miara zwijana4
4
Fit the bobs to the board
Fit the bobs to the board
Fasten one bob to one end of the board. Attach the other at the centre of its crosspiece with a bolt, so it can turn. Fasten the 1-3/4 by 2 in piece, 12 in long, across the top of the board at the front end.
Materiały do tego kroku:
Deska sosnowa1 sztuka
Deska z drewna liściastego1 sztuka
Śruba zamkowa1 sztuka
Podkładka płaska2 sztuk
Gwoździe1 sztukaPotrzebne narzędzia:
Świder korbowy z wiertłem
Piła ręczna
Młotek5
5
Fit the steering rope
Fit the steering rope
Fasten a rope to the knees of the front runners; it steers the sled.
Materiały do tego kroku:
Lina bawełniana1 sztukaPotrzebne narzędzia:
Świder korbowy z wiertłem6
6
Troubleshooting
Troubleshooting
Bobsled troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From "An Inexpensive Bobsled" by H. J. Blacklidge, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 49). Which end of the board gets the bolted bob, the bolt size and the stave length come only from his figure or are not given. The tools and metric figures are ours.
Materiały
7- 4 sztukZastępnik
- 1 sztukaZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
- 2 sztukZastępnik
- 1 sztukaZastępnik
Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.


