Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Self-Righting Jumping Hurdle: Off-Centre Pivoted Swing Between Two Standards (Boy Mechanic, 1915)
Woody

Autor

Woody

13. listopad 2026NO
7
0
0
0
0

Self-Righting Jumping Hurdle: Off-Centre Pivoted Swing Between Two Standards (Boy Mechanic, 1915)

C. C. Fraser's hurdle from The Boy Mechanic, Book 2 (1915): a 36 by 18 in swing hung on long nails slightly off centre between two standards joined by a reach. It turns at the slightest touch of the jumper's foot and rights itself again.
Początkujący
About 2 hours

Instrukcje

1

His cutting list in centimetres

Wczytywanie notatnika Jupyter…
2

Read The Boy Mechanic, Book 2

"The hurdle consists of two standards, a reach, and a swing."
3

Make the swing

Nail four pieces about 7/8 in thick and 1-1/2 in wide into a rectangle: two 36 in long and two 18 in long.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 sztuka
GwoździeGwoździe1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
MłotekMłotek
Miara zwijanaMiara zwijana
OłówekOłówek
4

Make the standards and reach

Make each standard of three pieces 7/8 in thick, 3 in wide and 18 in long, nailed firmly together as in his figure, and join their bases with a reach of the same stuff, 36 in long.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 sztuka
GwoździeGwoździe1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
MłotekMłotek
Miara zwijanaMiara zwijana
5

Hang the swing

Bore a hole in each standard large enough for a long nail to turn freely but too small for its head to pass, and hang the swing on the nails at its ends, slightly off centre, so it swings at a touch and rights itself.

Materiały do tego kroku:

GwoździeGwoździe1 sztuka

Potrzebne narzędzia:

Wiertarka ręcznaWiertarka ręczna
MłotekMłotek
6

Troubleshooting

Hurdle troubleshooting.

Flow

Loading...
7

History and honest limits

From "How to Make a Hurdle" by C. C. Fraser, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 145). How far off centre the pivots go is not given. The tools and metric figures are ours.

Materiały

2

Wymagane narzędzia

5
  • Zastępnik
  • Zastępnik
  • 1 vendor sell this, none ship to you yet
    Zastępnik
  • 1 vendor sell this, none ship to you yet
    Zastępnik
  • Zastępnik

Według tego planu powstaje

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...