Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)
Woody

Autor

Woody

13. listopad 2026NO
6
0
0
0
0

Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)

George J. Egelberg's ski sled from The Boy Mechanic, Book 3 (1919): "built low and wide so that it will not tip easily", on two 10 ft by 6 in ash runners boiled and bent like skis, set on knee blocks with a slight rocker, and topped with three 6 in boards.
Średniozaawansowany
About 2 days

Instrukcje

1

His sizes, and the rocker

Wczytywanie notatnika Jupyter…
2

Read The Boy Mechanic, Book 3

"The skis, or runners, are cut 10 ft. long and 6 in. wide, from 1-in. ash boards that are straight-grained."
3

Thin the bend

Cut two runners 10 ft long and 6 in wide from straight-grained 1 in ash. Where the curve will be, plane about 1/4 in off the upper side, but not at the very tip, so the skis bend more easily.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Strug ręcznyStrug ręczny
Miara zwijanaMiara zwijana
OłówekOłówek
4

Boil and bend

If steaming is not handy, boil the skis with at least 1-1/2 ft of the points under water and the vessel covered so little steam escapes, for at least one hour. Take them out, put them side by side in the bending blocks at once and bend with slow, even pressure; weight the long ends and leave them 8 or 10 hours to dry. Sharpen the points after bending.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 sztuka

Potrzebne narzędzia:

Duży garnekDuży garnek
Ścisk stolarski listwowyŚcisk stolarski listwowy
Strug ręcznyStrug ręczny
5

Set the blocks and top

For a slight rocker, make the centre knee block 6 in high and the two end blocks 5-1/2 in. Run a 1/4 in flat-head bolt through the ski, the block and the cross strip, countersinking the heads in the running surface. Make the top of three 6 in boards fastened to the crosspieces, and brace the ski tips with a 2 in strip.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Deska sosnowaDeska sosnowa3 sztuk
Śruba zamkowaŚruba zamkowa6 sztuk
Podkładka płaskaPodkładka płaska6 sztuk
Wkręty do drewnaWkręty do drewna1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Wiertarka ręcznaWiertarka ręczna
Zestaw pogłębiaczy stożkowychZestaw pogłębiaczy stożkowych
MłotekMłotek
6

Troubleshooting

Ski sled troubleshooting.

Flow

Loading...
7

History and honest limits

From "A Ski Sled" by George J. Egelberg, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, p. 41). The bending-block shape and knee pieces come from his drawing. The tools and metric figures are ours.

Materiały

5

Wymagane narzędzia

9

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...