SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Closed-Globe Egg Beater: Concentric Rings in a Shut Sphere
Martin

Autor

Martin

6. październik 2026NO
5
0
0
0
0

Closed-Globe Egg Beater: Concentric Rings in a Shut Sphere

Beaten in an open bowl, egg spatters and the air is not forced into it. James M. Jay of Canton, Ohio, received US 27,054, dated 7 February 1860, for an egg beater whose case is a hollow globe of two halves hinged and caught together; a horizontal shaft through it carries concentric rings, the outer one close to the inside so it sweeps the bottom, turned by a wheel and gear on a stand. "The air which occupies the upper part ... is so closely confined that it can not escape during the operation of beating the eggs, consequently it is carried down and mixed thoroughly with the eggs." This rung works out the air-to-egg ratio, then prints the ring dasher and gears, closes it in two bowls, and times a beating.
Średniozaawansowany
About 5 hours, plus printing

Instrukcje

1

Air shut in with the eggs

Wczytywanie notatnika Jupyter…
2

A dasher in a closed box before it

The embedded blueprint spins a dasher in a square box. Jay shuts the eggs in a globe so the air is driven into them.
3

Read US 27,054

"In my egg beater the air which occupies the upper part of the hollow bottom B, together with that which fills the cover or cap C, is so closely confined that it can not escape during the operation of beating the eggs, consequently it is carried down and mixed thoroughly with the eggs by the rings or dashes H', while the eggs are carried up and through the air in the cap or case C, so that a perfect mixture of the air and eggs is effected."
4

Print the rings and gears

Print the concentric-ring dasher (/uploads/blueprints/closed-globe-egg-beater-rings.stl), the 36-tooth wheel (/uploads/blueprints/closed-globe-egg-beater-wheel-36.stl) and the 12-tooth gear (/uploads/blueprints/closed-globe-egg-beater-gear-12.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.

Materiały do tego kroku:

Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
5

Make the globe

Take two matching bowls 120 mm across from the set. Drill both rims at opposite points for the shaft, 5.5 mm, so the shaft lies on the joint.

Materiały do tego kroku:

Zestaw misek do mieszaniaZestaw misek do mieszania1 sztuka

Potrzebne narzędzia:

Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
6

Shaft, rings and stand

Pass a 5 mm rod through one bowl's holes and the dasher's hub, and epoxy the hub at the centre. Epoxy the 12-tooth gear on the rod outside. Mount the 36-tooth wheel with a crank on an M5 screw on a hardwood upright so it meshes, and stand the lower bowl in a plywood ring.

Materiały do tego kroku:

Pręt ze stali niskowęglowejPręt ze stali niskowęglowej1 sztuka
Epoksyd dwuskładnikowyEpoksyd dwuskładnikowy1 sztuka
Klocek z drewna twardegoKlocek z drewna twardego1 sztuka
Płyta sklejkowaPłyta sklejkowa1 sztuka
Śruby maszynoweŚruby maszynowe1 sztuka
Podkładka płaskaPodkładka płaska1 sztuka
Nakrętka sześciokątnaNakrętka sześciokątna1 sztuka
Wkręt do drewna #8 x 1"Wkręt do drewna #8 x 1"1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Piłka włosowaPiłka włosowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
Zestaw wkrętakówZestaw wkrętaków
7

The patent drawing

US 27,054 drawing sheet, public domain (expired patent).
Krok 7 - Image 1
8

Closed against open

Beat two egg whites with the top bowl clamped on and time them to stiff peaks; then again with the top off. Compare the times and the volume of foam.
Krok 8 - Image 1

Materiały do tego kroku:

JajoJajo4 sztuk

Potrzebne narzędzia:

StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
9

A globe that leaks, rings that scrape

Closed-globe egg beater troubleshooting.

Flow

Loading...
10

History and honest limits

**James M. Jay** of Canton, Ohio, assignor to himself and John Danner, received US 27,054, dated 7 February 1860. The halves are turned to break joints and fit tight; a hook on the cover hangs on a pivot between lugs, and a swinging catch holds the cover down; the shaft's bearings are in the lower half's edge, the cover cut to fit over them. He wrote that it does not matter whether one or more eggs are beaten. **Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Two bought bowls stand in for his turned halves, without a hinge. Your times are the result.

Materiały

11

Wymagane narzędzia

10

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...