Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Christmas Tree Stand: Three Legs Tied by Wire Links to a Nail in the Butt (Cook, 1902)
Woody

Autor

Woody

13. listopad 2026NO
9
0
0
0
0

Christmas Tree Stand: Three Legs Tied by Wire Links to a Nail in the Butt (Cook, 1902)

William Cook of New York received US 710,762, dated 7 October 1902, for a Christmas tree stand of three leaning legs and three wire links. The links meet under the tree on a nail driven up into the butt, and their other ends are fixed part way up the legs. The tops of the legs are screwed to the trunk. The tree's weight pushes the feet out, the links pull back, and the tops of the legs squeeze the trunk. We make it from pine and steel wire. All sizes are ours.
Początkujący
About 3 hours

Instrukcje

1

Where the links go

Wczytywanie notatnika Jupyter…
2

Read US 710,762

"The tendency of legs A to spread by weight of tree causes an outward tension at wire nail F through the several links C and inward pressure on stem of tree by upper part of legs A. Thus the tree is held very secure and perfectly upright by two opposite forces acting a short space apart and derived from weight of tree."
3

Cut the legs

Saw three legs 700 mm long from 70 x 22 mm pine (ours). Set a bevel gauge to 30 degrees and cut both ends of each leg at that angle, parallel to each other, so the foot sits flat on the floor and the top lies along the trunk, as in his Fig. 2. Sand off the splinters.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Kątomierz nastawnyKątomierz nastawny
Miara zwijanaMiara zwijana
OłówekOłówek
Papier ściernyPapier ścierny
4

Bend the links

Cut three pieces of 2.5 mm steel wire, each the link length from the notebook plus about 60 mm for the eyes. Bend a round eye at each end with round-nose pliers, as his Fig. 3, so the eyes' centres are the link length apart. Make all three the same.

Materiały do tego kroku:

Drut stalowyDrut stalowy3 sztuk

Potrzebne narzędzia:

Obcinaki boczneObcinaki boczne
Szczypce okrągłeSzczypce okrągłe
Miara zwijanaMiara zwijana
5

Staple the links to the legs

Mark each leg where the notebook says, on its inner face. Bend three U staples from the same wire (ours). Lay a link's outer eye on the mark and drive a staple over it into the leg, his staple H, leaving the eye free to turn.

Materiały do tego kroku:

Drut stalowyDrut stalowy1 sztuka

Potrzebne narzędzia:

Obcinaki boczneObcinaki boczne
Szczypce okrągłeSzczypce okrągłe
Młotek ciesielskiMłotek ciesielski
6

Drill the tops of the legs

Drill a hole through the top of each leg, about 40 mm from its end, just big enough for the screw eye's shank to pass.

Potrzebne narzędzia:

Wiertarka ręcznaWiertarka ręczna
7

Nail the links to the butt

Saw the butt of the tree off square. Lay the tree on its side. Thread a long wire nail through the three free eyes of the links, his nail F, and drive it up into the middle of the bottom end of the tree.

Materiały do tego kroku:

GwoździeGwoździe1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Młotek ciesielskiMłotek ciesielski
8

Fix the tops of the legs

Bring the top of each leg in against the trunk. Make a start hole in the trunk with an awl through the leg's hole, and turn a screw eye through the leg into the trunk until the leg is held tight, his screw-eye D. Do all three, then stand the tree up.

Materiały do tego kroku:

Hak oczkowy wkręcanyHak oczkowy wkręcany3 sztuk

Potrzebne narzędzia:

SzydłoSzydło
9

Check it stands upright

All three feet should touch the floor and the links should be straight and tight. Look at the tree from two sides. To take it down, turn out the screw eyes and pull the nail; the links fold about the nail for storing.
10

Troubleshooting

Christmas tree stand troubleshooting.

Flow

Loading...
11

History and honest limits

**William Cook** of New York, US 710,762, dated 7 October 1902, filed 29 July 1901. He claimed "a Christmas-tree stand composed of legs, and links, one end of each link being connected with one leg at a point intermediate between the ends of the leg, and the opposite ends of the links being connected with each other to form a seat". He says the stand is "more economical of construction and more easily applied" and that "size of tree offers no obstacle". He names no materials and gives no sizes: the pine, the wire, the 700 mm legs, the 30 degree angle, the butt height and how the screw eyes pass through the legs are ours. His drawing also marks parts E and G, which his text does not describe.

Materiały

4

Wymagane narzędzia

10

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...