Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Digital Tachometer: Hand-Held Contact Type That Holds Its Reading (Sugiyama, Shimpo, US 4,000,465, 1976)
Ed

Autor

Ed

3. listopad 2026FI
13
0
0
0
0

Digital Tachometer: Hand-Held Contact Type That Holds Its Reading (Sugiyama, Shimpo, US 4,000,465, 1976)

A hand-held digital tachometer. You press the contact head on its shaft against the end of a turning shaft and push the thumb button; a slotted disk inside chops a light beam into pulses, and the pulses counted in a fixed time, set by a quartz clock, appear in the window as the speed. A latch holds the reading after you take the tachometer away, so you can read it even where you could not see the window while measuring. Result: a contact tachometer that shows revolutions per unit time and keeps the last reading. Source: Y. Sugiyama (Shimpo Kogyo), US 4,000,465 (1976). Unknown: the number of holes, the clock, the gate time and the circuit details. Picture: the patent drawing.
Zaawansowany
Unknown

Instrukcje

1

Make the housing and measuring shaft

Make a cylindrical housing to hold in one hand, with a window in its side for the reading and a push button for the power switch where the thumb falls. Run a measuring shaft out of the front end in bearings and fit a contact head on its tip to press against the shaft being measured. Not given: materials, sizes. Ours: aluminium tube, a ball bearing.

Materiały do tego kroku:

Rura aluminiowaRura aluminiowa1 housing
Nieznany metalNieznany metal1 measuring shaft
Łożysko kulkoweŁożysko kulkowe1 sztuka
Nieznany materiałNieznany materiał1 contact head

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
Wiertarka ręcznaWiertarka ręczna
Nieznane wymiaryNieznane wymiary
2

Make the pulse generator

Fix a disk on the measuring shaft with a ring of small holes evenly spaced near its edge. Put a light source on one side of the disk and a photodetector on the other: each hole passing makes one pulse. Shape and amplify the pulses. Not given: the number of holes. Ours: an LED and a photodiode.

Materiały do tego kroku:

Nieznany materiałNieznany materiał1 slotted disk
Zestaw diod LEDZestaw diod LED1 light source
Fotodioda (BPW34)Fotodioda (BPW34)1 photodetector
Opór elektrycznyOpór elektryczny1 zestaw

Potrzebne narzędzia:

Wiertarka ręcznaWiertarka ręczna
3

Build the counting circuit

Divide a quartz oscillator's clock down to gate pulses one unit of time long. Pass the measurement pulses through an AND gate during each gate pulse into a counter. At the start of each gate pulse a reset pulse clears the counter. After the gate pulse ends, the first measurement pulse that arrives triggers a latch pulse that loads the new count into the display. If the head has been taken off the shaft, no pulse arrives, no latch pulse is made, and the display keeps the last reading until the next measurement or until the power is switched off. Not given: the clock frequency and gate time. Ours: logic ICs and a seven-segment display.

Materiały do tego kroku:

Płytka drukowanaPłytka drukowana1 sztuka
Rezonator kwarcowyRezonator kwarcowy1 sztuka
Zestaw układów logicznychZestaw układów logicznych1 divider, AND gate, counter, latch, reset
Sterownik wyświetlacza siedmiosegmentowegoSterownik wyświetlacza siedmiosegmentowego1 sztuka
Czterocyfrowy wyświetlacz siedmiosegmentowyCzterocyfrowy wyświetlacz siedmiosegmentowy1 sztuka
Drut lutowniczyDrut lutowniczy1 as needed

Potrzebne narzędzia:

LutownicaLutownica
4

Power it and measure

Fit the battery and the thumb button as the power switch. Press the contact head against the end of the turning shaft so it turns with it, push the button, and read the revolutions in the window, now or after you take the tachometer away.

Materiały do tego kroku:

AkumulatorAkumulator1 sztuka
PrzyciskPrzycisk1 sztuka

Potrzebne narzędzia:

LutownicaLutownica

Materiały

15

Wymagane narzędzia

4

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...