Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Distillation Column Assembly: Flask, "Evaporator" Still-Head, Liebig Condenser and Receivers (Young, 1903)
Charlie

Autor

Charlie

3. listopad 2026DE
10
0
0
0
0

Distillation Column Assembly: Flask, "Evaporator" Still-Head, Liebig Condenser and Receivers (Young, 1903)

A complete fractional distillation set: a globular flask, Young and Thomas's 'evaporator' still-head built of stacked glass sections, a Liebig condenser and a row of receivers. In each section the rising vapour is forced through the liquid running back down, so the mixture separates better at each step. Result: a fractionating apparatus for separating liquids by boiling point, the fractions caught in receivers changed at set temperatures. Source: S. Young, Fractional Distillation (1903), pp. 4-7, 115-116, 166-168. Picture: Figs. 37 and 38 of the book.
Zaawansowany
Unknown

Instrukcje

1

Choose the still

Use a globular flask, since a flat-bottomed one may crack over a naked flame, no larger than the amount of liquid needs. Fit it with a cork for the still-head. Ours: a round-bottom flask.

Materiały do tego kroku:

Kolba kulistaKolba kulista1 still
KorkiKorki1 still cork

Potrzebne narzędzia:

Palnik BunsenaPalnik Bunsena
2

Blow the evaporator still-head

Build the still-head of sections joined end to end. Each outer tube is 22 to 24 mm inside and about 10 to 10.5 cm long, constricted at the bottom. In it stands a thin inner tube, 7.5 to 8 mm inside and 60 mm long, open at both ends, with two large holes near its top. Its lower end widens into a funnel resting on the constriction, with three or four tiny glass beads fused to the rim so it does not fit too tightly. Over it stands an intermediate tube about 14 mm inside and 50 mm long, like a small inverted test tube. A small funnel, slightly wider than the dip in the outer tube above, sits on top of it on three glass legs. Small glass projections centre the tubes. Make the head long enough that the thermometer's bulb and stem both sit in the vapour, with a side delivery tube at the top.

Materiały do tego kroku:

Rurka szklanaRurka szklana1 sections, inner and intermediate tubes, delivery tube

Potrzebne narzędzia:

Palnik stołowy do dmuchania szkłaPalnik stołowy do dmuchania szkła
3

Fit the condenser

Use a Liebig condenser, about 7 or 8 mm inside for the inner tube and 15 mm for the outer, cooled by running water. Pass the delivery tube through a cork into it. Draw out the joint where the wide inlet meets the narrow tube so no pool of liquid lies there. Bend the narrow tube so the condenser can stand upright. Above about 170 °C use a long tube cooled by air instead of water.

Materiały do tego kroku:

Chłodnica wodnaChłodnica wodna1 condenser
KorkiKorki1 condenser cork

Potrzebne narzędzia:

Palnik stołowy do dmuchania szkłaPalnik stołowy do dmuchania szkła
WodaWoda
4

Set the heat and the receivers

Heat with a Bunsen burner, its top about 2 mm below the flask so the small flame touches the glass, shielded from draughts. Add a few pieces of porous porcelain (a broken clay pipe will do) or pumice if the liquid bumps. Set a thermometer in the still-head and a row of small flasks as receivers.

Materiały do tego kroku:

TermometrTermometr1 still-head thermometer
Kolba zbiorczaKolba zbiorcza10 receivers

Potrzebne narzędzia:

Palnik BunsenaPalnik Bunsena
Nieznany materiałNieznany materiał
5

Distil in fractions

Read the barometer and correct the set temperatures for it. Distil steadily. In each section, condensed liquid seals the narrow passage, so the vapour rises up the inner tube, down between the tubes and up again, while liquid drips from section to section back to the still. Collect the distillate in fractions, changing the receiver each time the temperature reaches one of the values fixed beforehand.

Potrzebne narzędzia:

Barometr rtęciowyBarometr rtęciowy
Palnik BunsenaPalnik Bunsena
WodaWoda

Materiały

6
  • Zastępnik
  • 1 condenser cork
    Zastępnik
  • 1 sections, inner and intermediate tubes, delivery tube
    Zastępnik
  • 1 condenser
    Zastępnik
  • 1 still-head thermometer
    Zastępnik
  • 10 receivers
    Zastępnik

Wymagane narzędzia

5

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...