Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Brick Smith's Hearth: Stone Base, Firebrick Top in an Iron Rim, a Cannon-Shot Tuyere and a Slake Trough (Edwinson, 1886)
Forge

Autor

Forge

14. listopad 2026NO
7
0
0
0
0

Brick Smith's Hearth: Stone Base, Firebrick Top in an Iron Rim, a Cannon-Shot Tuyere and a Slake Trough (Edwinson, 1886)

The fixed smith's hearth George Edwinson told Amateur Work readers to build (1886): stone below, firebrick in fireclay on top, every course bound with hoop iron, a 4 in. iron rim forming the hearth pan, a fire back and tuyere made from a 1 in. plate and a bored 14-pounder iron shot, a slanting flue, a 10 x 10 x 22 in. slake trough, and a clinker floor.
Średniozaawansowany
Two to three days of building

Instrukcje

1

His sizes

Wczytywanie notatnika Jupyter…
2

Read Edwinson

"The foundation of this structure up to within one foot of the top may be of stone, but the finishing courses should be of firebrick."
3

Build the base

Build the hearth in stone up to 1 ft (30 cm) below the top, binding every course with pieces of hoop iron. Leave an arch at the back for the coal pit and the blast pipe (figs. 4, 5). Overall size is ours: fit it to your shop.

Materiały do tego kroku:

Blok kamiennyBlok kamienny1 sztuka
Obręcz żelaznaObręcz żelazna1 sztuka
Glina ogniotrwałaGlina ogniotrwała1 sztuka

Potrzebne narzędzia:

KielniaKielnia
PoziomicaPoziomica
4

Make the fire back and tuyere

Bore a 3/4 in. hole through a 14-pounder iron shot and open it to a 1 in. taper on one side. Cut and countersink a hole in a 1 in. iron plate to take a third of the shot, and drill four 1/2 in. holes to bolt the plate through the wall with nuts and fish plates. (Or buy a fire back and tue-iron.)

Materiały do tego kroku:

Śrut żelazny (balast)Śrut żelazny (balast)1 sztuka
Płyta żelaznaPłyta żelazna1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych1 sztuka

Potrzebne narzędzia:

Wiertarka stołowaWiertarka stołowa
Kuźnia kowalskaKuźnia kowalska
MłotekMłotek
5

Firebrick top and back

Lay the top courses and the back wall round the tuyere in firebrick bedded and jointed with fireclay, still binding each course with hoop iron. Build in the fire back with the shot as the tuyere, and leave a slanting flue hole just above it (fig. 5).

Materiały do tego kroku:

Cegły szamotoweCegły szamotowe1 sztuka
Glina ogniotrwałaGlina ogniotrwała1 sztuka
Obręcz żelaznaObręcz żelazna1 sztuka

Potrzebne narzędzia:

KielniaKielnia
PoziomicaPoziomica
6

Fit the slake trough

Before the last course, set in a water trough 10 in. deep and wide and 22 in. long, of sheet iron, cast iron or stone, inside the rim line; bolt a sheet-iron one to the rim. A sheet-iron division riveted across gives a coal trough too.

Materiały do tego kroku:

Blacha ze stali miękkiejBlacha ze stali miękkiej1 sztuka
Nity żelazneNity żelazne1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Wiertarka stołowaWiertarka stołowa
MłotekMłotek
7

Bind with the rim

Bind the top course with a rim of 1/4 x 4 in. iron, half below the brick edge and half above it to make the hearth pan, its ends bolted to the back wall with 3/8 in. bolts built into the brickwork.

Materiały do tego kroku:

Płyta żelaznaPłyta żelazna1 sztuka
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych1 sztuka

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
KowadłoKowadło
MłotekMłotek
Wiertarka stołowaWiertarka stołowa
8

Connect the blast

Bring the pipe from a fan or bellows under the arch to the back of the tue-iron. He reckons about 150 cu ft (4.2 m3) of air a minute for a welding heat: a 9 in. fan at about 360 rpm or a double-action bellows.

Potrzebne narzędzia:

DmuchawaDmuchawa
9

Lay the floor

Ram wetted smiths', foundry or boiler clinkers sprinkled with a little Portland cement hard and level, with a thin layer of smithy cinder ashes beaten on top. Stone or ordinary concrete floors misbehave when hot iron is dropped on them.

Materiały do tego kroku:

Cement portlandzkiCement portlandzki1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

MłotekMłotek
10

Troubleshooting

Hearth troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" I, **Amateur Work, Illustrated**, vol. V (1886), pp. 161-162 and figs. 2, 4, 5 (checked on the archive.org scan amateurworkillus05lond). He gives no overall hearth size; that and the metric figures and tools are ours.

Materiały

11

Wymagane narzędzia

7

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...