Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)
Forge

Autor

Forge

14. listopad 2026NO
7
0
0
0
0

Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)

Swages, the smith's top and bottom tools for bringing a weld back to round or square, from George Edwinson's smithing series in Amateur Work (1886): steel or steel-faced iron made like a fuller, the bottom tool tanged for the anvil's square hole, the top tool on a withy or iron-rod handle, or the pair coupled by a steel spring for single-handed work.
Zaawansowany
A day at the forge per pair

Instrukcje

1

Read Edwinson

"They may be made of steel throughout, or of steel-faced iron. The method of making them is similar to that for making fullers and setts."
2

Weld the blanks

As for a fuller: upset an iron bar, split it into a fork with a hot set, weld in a forged steel wedge. Or use steel throughout.

Materiały do tego kroku:

Pręt z kutego żelazaPręt z kutego żelaza1 sztuka
Stal tyglowaStal tyglowa1 sztuka
Boraks w proszkuBoraks w proszku1 sztuka

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
KowadłoKowadło
Młot dwuręcznyMłot dwuręczny
Przecinak na gorącoPrzecinak na gorąco
Szczypce kowalskieSzczypce kowalskie
3

Bottom swage

Forge the steel face into a block with a square tang that fits the square hole in the tail of the anvil, like a bottom set (his figs. 285-288).

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
KowadłoKowadło
MłotekMłotek
Szczypce kowalskieSzczypce kowalskie
4

Top swage

Forge the matching top tool with a neck for its handle.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
KowadłoKowadło
MłotekMłotek
Szczypce kowalskieSzczypce kowalskie
5

Cut the grooves

Form the working groove in each face to the section you need: round, half-round, oval, diagonal, square or rectangular. Groove sizes are ours: match the bars you forge.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Fuller (żelazo do rowkowania)Fuller (żelazo do rowkowania)
KowadłoKowadło
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
6

Handle or spring

Give the top tool a hazel-rod or iron-rod handle as for fullers and top sets. For single-handed work, couple the top and bottom tools with a steel spring (fig. 283).

Materiały do tego kroku:

Pręty leszczynowe (zielone, giętkie)Pręty leszczynowe (zielone, giętkie)1 sztuka
Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej1 sztuka
Drut żelaznyDrut żelazny1 sztuka
Taśma ze stali sprężynowejTaśma ze stali sprężynowej1 sztuka

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
KowadłoKowadło
MłotekMłotek
7

Grind and harden

Grind the faces level so they fit each other, then heat the whole tool and harden it (his note for hand-worked dies).

Potrzebne narzędzia:

ToczydłoToczydło
Kuźnia kowalskaKuźnia kowalska
Kadź hartowniczaKadź hartownicza
8

Use them

Work the weld at a red heat. Hold the bar and the top swage; the striker hits the top tool with a light sledge. Pass the bar to and fro, turning it for round. After each heat gauge the weld in the swage block or with callipers.

Potrzebne narzędzia:

Kuźnia kowalskaKuźnia kowalska
Młot dwuręcznyMłot dwuręczny
SuwmiarkaSuwmiarka
9

Troubleshooting

Swage troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" XI, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 259-260 and figs. 283-290 (checked on the archive.org scan amateurworkillus06lond). The forging steps follow his fuller method (pp. 14-16). Groove sizes, the spring stock and the tools are ours.

Materiały

7

Wymagane narzędzia

11

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...