Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Electromagnet: Horseshoe Holding Magnet Sized by Its Pull (Underhill, 1903)
Volt

Autor

Volt

3. listopad 2026SE
10
0
0
0
0

Electromagnet: Horseshoe Holding Magnet Sized by Its Pull (Underhill, 1903)

A holding electromagnet in its practical horseshoe form: two iron cores, each wound with wire, fastened to an iron yoke, and an iron armature across the poles. You size it from the pull you need: the pull sets the pole area, and the supply voltage sets the wire. Variable: the pull. Each pound needs a set area of pole, depending on the iron. Source: C. R. Underhill, The Electromagnet (1903), pp. 92, 106-118, 150. Unknown: sizes and the ampere-turns. Picture: Fig. 51 of the book.
Średniozaawansowany
Unknown

Instrukcje

1

Size the poles from the pull

Pull P (pounds) = B² × A / 72,134,000, where B is the flux density in lines per square inch and A the pole area in square inches. Working densities: wrought iron 90,000, cast steel 85,000, Mitis iron 80,000, ordinary cast iron 50,000, which give 112.3, 100.1, 88.72 and 34.66 lb per square inch of pole. Divide the pull you need by that figure to get the pole area. Underhill's example, for cast steel taken at 90,000: 10 lb needs 0.089 square inch, a core 0.336 inch across. A two-pole magnet holds twice the weight of a single pole at the same induction.

Potrzebne narzędzia:

Nieznane wymiaryNieznane wymiary
2

Make the cores, yoke and armature

Make the practical horseshoe magnet in three pieces besides the armature: two round cores and a yoke (back iron) to join them. Make an armature to lie across the two pole ends. Face the poles and the armature accurately; an uneven contact spreads the lines unevenly and weakens the pull. Ours: wrought iron. Not given: sizes, how the cores are fastened.

Materiały do tego kroku:

Pręt z kutego żelazaPręt z kutego żelaza1 two cores, yoke, armature

Potrzebne narzędzia:

Tokarka do metaluTokarka do metalu
Nieznane wymiaryNieznane wymiary
3

Choose the wire for the supply

Design the coil to stand the full supply voltage without overheating; never put a resistor in series with the magnet, as that wastes power and makes the magnet weaker. Pick the wire size that makes the coil's resistance equal to that of the line and the source, then try the next larger size, and keep the one giving more ampere-turns. A coil rises about 100 °F at about 0.9 watt per square inch of surface for a thin telephone-ringer coil, or 0.33 for a thick one (4 1/8 in across, 7 in long, 1 7/16 in thick), and the rise grows in proportion to the watts. Ours: the supply, e.g. 12 V.

Potrzebne narzędzia:

Zasilacz prądu stałegoZasilacz prądu stałego
Nieznane wymiaryNieznane wymiary
4

Wind the cores and fasten them to the yoke

Wind the wire directly onto each core between insulating end heads, and fasten the wound cores to the yoke. The joints between cores and yoke lose a little pull. Ours: enamelled copper wire. Not given: the winding method, the insulation.

Materiały do tego kroku:

Drut miedziany emaliowanyDrut miedziany emaliowany1 two coils
Nieznany materiał izolacyjnyNieznany materiał izolacyjny1 end heads and core insulation
Nieznany metalNieznany metal1 core fastenings

Potrzebne narzędzia:

Nieznana metoda nawijaniaNieznana metoda nawijania
Tokarka do metaluTokarka do metalu
5

Switch on and hold

Connect the coils to the supply and put the armature against the faced poles: the magnet holds it with the pull it was sized for. When the armature touches the poles there is practically no leakage between them.

Potrzebne narzędzia:

Zasilacz prądu stałegoZasilacz prądu stałego

Materiały

4

Wymagane narzędzia

4

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...