Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Four-Crank Gyrating Churn: Four Cranks Carry the Tub Round a Small Circle With No Dasher
Martin

Autor

Martin

10. listopad 2026NO
8
0
0
0
0

Four-Crank Gyrating Churn: Four Cranks Carry the Tub Round a Small Circle With No Dasher

Alfred Guthrie of Chicago received US 24,907, dated 26 July 1859, for a churn with no dasher at all. Four upright shafts in a frame have cranks on their tops, and a bed plate lies over the four crank pins, so each crank turns on its own centre but all move together. The tub stands on the plate, held by stirrups, and is carried round a small circle, throwing the cream against its sides. A handle turns one crank shaft through cogged gearing. This rung builds it at the patent's own sizes: a frame about two feet square and one foot high, shafts of 3/4 inch iron and 3 inch cranks.
Średniozaawansowany
About 2 days, plus printing

Instrukcje

1

How hard the cream is swung

Wczytywanie notatnika Jupyter…
2

A churn with a dasher, before it

Wineman's dasher drove the cream through holes. Guthrie did away with the dasher and moved the whole tub.
3

Read US 24,907

"I connect the whole together by the bed plate D over the wrists of each crank E, E, E, E. Each crank will revolve upon its own center but will each correspond to the motion of the other."
4

Print the wheel H

The 64-tooth spur wheel (module 3, 198 mm across) for the handle shaft I, with a 20 mm bore. PETG, 0.2 mm layers, 50 % infill, 5 walls.
Plik projektowySTLCC0 - Free
5

Print the pinion H

The 24-tooth spur pinion for the driven crank shaft, with a 19 mm bore and a hub. PETG, 0.2 mm layers, 50 % infill, 5 walls.
Plik projektowySTLCC0 - Free
6

Frame and bearing bars

Build a pine frame 610 mm square and 305 mm high: four 50 mm corner posts, and 50 mm rails round the top and the bottom. Fit two hardwood bars across it, top and bottom, 150 mm in front of and behind the middle, and bore them 19.6 mm square to the frame at 200 mm either side of the middle, for the four shafts. Screw two hardwood brackets to the right side, top and bottom, bored 20.6 mm 132 mm out from the front right shaft, for the handle shaft.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa2 sztuk
Drewno iglaste 70x70 mmDrewno iglaste 70x70 mm2 sztuk
Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Wkręt do drewna nr 10 x 3"Wkręt do drewna nr 10 x 3"24 sztuk
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Kątownik stolarskiKątownik stolarski
PoziomicaPoziomica
Miara zwijanaMiara zwijana
7

Shafts, cranks and plate D

Cut four 19 mm steel shafts 323 mm long and stand them in the bars. Make four hardwood crank arms, 76 mm from the shaft to the crank pin, and pin them on the shafts' tops all pointing the same way. Fit a 19 mm steel crank pin 50 mm long in each. Cut plate D 532 mm across from plywood, bore it for the four pins exactly where they stand, and drop it on them. Turn one crank by hand: the plate must run round freely without turning.

Materiały do tego kroku:

Pręt stalowy surowyPręt stalowy surowy2 sztuk
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Płyta sklejkowaPłyta sklejkowa1 sztuka
Podkładka płaskaPodkładka płaska8 sztuk
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych4 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową4 sztuk
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)
Imadło warsztatoweImadło warsztatowe
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
WyrzynarkaWyrzynarka
Miara zwijanaMiara zwijana
Klucz nastawnyKlucz nastawny
8

Gearing H and handle I

Pin the pinion on the front right shaft 140 mm up. Stand a 20 mm steel shaft 885 mm long in the brackets, pin the wheel on it level with the pinion, and check they mesh fully. Fix a hardwood handle arm 150 mm long on the shaft's top with a dowel grip.

Materiały do tego kroku:

Filament PETGFilament PETG1 sztuka
Pręt stalowy surowyPręt stalowy surowy1 sztuka
Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Piła do metaluPiła do metalu
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
9

Tub F on its grooved bottom

Glue a plywood ring to the plate's middle, 282 mm inside and 340 mm outside, so the bucket's foot sits in it. Bend two flat-bar stirrups to go up the bucket's sides and over its lid, notch the ring for them and bolt them to the plate.

Materiały do tego kroku:

Płyta sklejkowaPłyta sklejkowa1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej2 sztuk
Zestaw śrub sześciokątnychZestaw śrub sześciokątnych4 sztuk
Nakrętka samohamowna z wkładką nylonowąNakrętka samohamowna z wkładką nylonową4 sztuk
Wiadro 20-litroweWiadro 20-litrowe1 sztuka

Potrzebne narzędzia:

WyrzynarkaWyrzynarka
Imadło warsztatoweImadło warsztatowe
Piła do metaluPiła do metalu
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Klucz nastawnyKlucz nastawny
10

The build in 3D

FreeCAD model of this build: the frame with its bearing bars, the four shafts and cranks, plate D on the crank pins, the bucket in its ring under two stirrups, and the spur wheel on the handle shaft driving the pinion. It was checked at eight crank angles.
Plik projektowyBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, put the lid on and tighten the stirrups. Turn the handle steadily and time it. When the butter comes, lift the bucket off, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka8 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
12

Troubleshooting

Four-crank churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Alfred Guthrie** of Chicago, Illinois, assignor to Wardell Guthrie, US 24,907, 26 July 1859, "Churn". He claimed the cranks C connected by the plate D. His sizes are kept: a frame about two feet square and one foot high, shafts of 3/4 inch iron about a foot long, and cranks of 3 inches, which we read from "about a six inch throw or three inches" and Fig. 3's "3 in" marks. He gives no gear sizes; ours are printed spur gears placed as his Figs. 2-3 draw them. Every other size is ours.

Materiały

17

Wymagane narzędzia

17

Pliki projektowe

3

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...