Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Saddler's Stitching Clam From Two Oak Barrel Staves on a Dovetailed Deal Base (Hasluck, Harness Making, 1904)
Woody

Autor

Woody

14. listopad 2026NO
6
0
0
0
0

Saddler's Stitching Clam From Two Oak Barrel Staves on a Dovetailed Deal Base (Hasluck, Harness Making, 1904)

The home-made saddler's clamp from P. N. Hasluck's Harness Making (1904): two curved oak barrel staves, 2 ft long, screwed into a dovetail tenon on a 20 in deal block so their thinned upper ends spring tightly together as jaws. Held slanting between the knees, it grips the work while both hands stitch.
Średniozaawansowany
About half a day

Instrukcje

1

Parts in centimetres

Wczytywanie notatnika Jupyter…
2

Read Harness Making

"A clamp can be made easily by the worker at home."
3

Shape the staves

Cut two oak cask or barrel staves 2 ft long and at least 3 in wide, the most curved part in the centre (the more bent, the more useful). Clean the outside with a spokeshave, leaving one end the full thickness (about 1 in) and thinning gradually to about 3/4 in toward the upper ends, which form the jaws (Fig. 55). Round the outer corners, flatten the inside, and glass-paper both sides.

Materiały do tego kroku:

Klepka beczkiKlepka beczki2 sztuk

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Strug kabłąkowyStrug kabłąkowy
Papier ściernyPapier ścierny
4

Cut the base

Cut the lower part C from sound white deal, 20 by 3 by 3 in, with a dovetail-shaped tenon at least 6 in long. Fit the shoulders and the width of its upper end to the curve of your staves so that it takes energetic screwing to bring the staves home and their jaws press tightly together.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
DłutaDłuta
Pobijak drewnianyPobijak drewniany
Strug ręcznyStrug ręczny
5

Screw together

Screw the staves to the tenon with eight stout 2-1/4 in screws, countersunk flush (Fig. 54).

Materiały do tego kroku:

Wkręty do drewnaWkręty do drewna8 sztuk

Potrzebne narzędzia:

Świder korbowy z wiertłemŚwider korbowy z wiertłem
Zestaw pogłębiaczy stożkowychZestaw pogłębiaczy stożkowych
Wkrętak płaskiWkrętak płaski
6

Use it

Hold the clamp slanting between the knees, resting against the left knee, with the right leg thrown over it, so the work is held fast between the jaws and both hands are free for the awl and two needles.
7

Troubleshooting

Clamp troubleshooting.

Flow

Loading...
8

History and honest limits

From Paul N. Hasluck, **Harness Making** (1904), "Harness-makers' Tools" (checked on the archive.org scan harnessmaking00hasl, pp. 24-27). The tools and metric figures are ours.

Materiały

3

Wymagane narzędzia

9

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...