Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Craftsman Leather Billfold: Two Cardboard Patterns, Silk Lining and Saddle-Stitched Waxed Silk (Boy Mechanic, 1919)
Tex

Autor

Tex

13. listopad 2026FO
14
0
0
0
0

Craftsman Leather Billfold: Two Cardboard Patterns, Silk Lining and Saddle-Stitched Waxed Silk (Boy Mechanic, 1919)

Livingston Haviland's billfold from The Boy Mechanic, Book 3 (1919): two leather body parts cut to stiff-cardboard patterns (13-1/4 and 8-3/16 by 4-1/4 in), lined with skiver or silk moire, folded into two card pockets and a money compartment, glued, and hand-sewn with heavy waxed silk 3/16 in from the edges.
Średniozaawansowany
About 1 day

Instrukcje

1

His patterns in centimetres

Wczytywanie notatnika Jupyter…
2

Read The Boy Mechanic, Book 3

"The making of a billfold is easily within the range of an amateur in leather work, who will observe the instructions carefully." Seal, morocco, pigskin and ooze sheep are all satisfactory.
3

Cut the patterns and the leather

Cut two patterns of stiff cardboard (Fig. 1). Body part No. 1: 13-1/4 by 4-1/4 in, with fold lines at 2-1/2, 2-5/8, 3, 2-5/8 and 2-1/2 in, and each end (A, B) cut in with 1/2 in radius arcs, set in 1/4 in. Body part No. 2: 8-3/16 by 4-1/4 in, with fold lines at 2-19/32, 3 and 2-19/32 in. Lay each pattern on the leather and trim the leather even with it, guiding the knife with a metal straightedge, on a close-grained hardwood board or a piece of sheet zinc.

Materiały do tego kroku:

Skóra świńskaSkóra świńska1 sztuka
Kartonowe arkusze na szablonyKartonowe arkusze na szablony1 sztuka

Potrzebne narzędzia:

OłówekOłówek
LinijkaLinijka
Liniał krawędziowyLiniał krawędziowy
Nóż introligatorskiNóż introligatorski
Deska z drewna liściastegoDeska z drewna liściastego
Blacha cynkowaBlacha cynkowa
4

Line the parts

Cut linings slightly larger than the patterns. Skiver is glued all over with a good, pliable leather glue that will not crack the leather; smooth it on gently without stretching, or the leather may buckle, and dry it under a light weight. Silk moire is glued with a thin stripe round the edges only, left to overhang, and trimmed off neatly when dry.

Materiały do tego kroku:

Tkanina jedwabnaTkanina jedwabna1 sztuka
Klej do skóryKlej do skóry1 sztuka

Potrzebne narzędzia:

NożyczkiNożyczki
Nóż introligatorskiNóż introligatorski
5

Glue and fold

Fold part No. 1 to form the back and the two card pockets. Apply stripes of glue as shown in Fig. 3, drop part No. 2 (the money compartment) into place, and fold the ends of No. 1 over on the dotted lines. Weight the billfold and let the glue dry.

Materiały do tego kroku:

Klej do skóryKlej do skóry1 sztuka

Potrzebne narzędzia:

Modelarka do skóryModelarka do skóry
6

Mark and punch the stitching

Draw a straight line with a blunt-point tool along the edges to be sewn, 3/16 in from them. Mark the stitch spacing for an inch on a strip of paper and transfer it along the line. Punch the holes on a pine board with a diamond-pointed awl held vertical (D); back the open ends with strips of cardboard while punching.

Potrzebne narzędzia:

Modelarka do skóryModelarka do skóry
LinijkaLinijka
Szydło do podeszwySzydło do podeszwy
Deska sosnowaDeska sosnowa
Kartonowe arkusze na szablonyKartonowe arkusze na szablony
7

Sew and finish the edges

Sew with heavy waxed silk matching the leather, by hand or with the work clamped between two boards. Thread a needle on each end, start both from the right side (E), pass the needle from the first hole through the second (F) and, with the needles in position (G), continue this stitch. Tie the ends neatly. Trim the edges and tool them smooth with a suitable metal tool or rod, heated moderately, applying water with the fingertip.

Materiały do tego kroku:

Nić jedwabnaNić jedwabna1 sztuka
Wosk pszczeliWosk pszczeli1 sztuka

Potrzebne narzędzia:

Dwie igły rymarskieDwie igły rymarskie
NożyczkiNożyczki
Nóż introligatorskiNóż introligatorski
Pręt okrągły ze stali niskowęglowejPręt okrągły ze stali niskowęglowej
8

Troubleshooting

Billfold troubleshooting.

Flow

Loading...
9

History and honest limits

From "A Craftsman Leather Billfold" by Livingston Haviland, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 446-447). He does not give the number of stitches to the inch or what waxes the silk (beeswax is ours). Pigskin is one of his four leathers. The tools and metric figures are ours.

Materiały

6

Wymagane narzędzia

13

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...