Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Tooled Calfskin Coin Purse: Lined, Flap Over Front, Design Split Between Flap and Front (Boy Mechanic, 1915)
Tex

Autor

Tex

13. listopad 2026FO
7
0
0
0
0

Tooled Calfskin Coin Purse: Lined, Flap Over Front, Design Split Between Flap and Front (Boy Mechanic, 1915)

The first piece in Mary C. Scovel's leather course (The Boy Mechanic, Book 2, 1915): a coin purse of Russian calfskin from a 4 by 8 in piece, its design traced, lined and tooled or stamped, split so half sits on the flap and half on the front below it, then lined with silk and stitched.
Początkujący
About 3 hours

Instrukcje

1

Her sizes in centimetres

Wczytywanie notatnika Jupyter…
2

Read The Boy Mechanic, Book 2

Her outfit: "two special tools costing 50 cents each, one with a narrow edge for lining patterns, and one with broad ends for tooling; and a piece of tin, plate glass, or very smooth hard wood, which should not be smaller than 9 by 12 in. A soft sponge, a triangle, a rule, tracing paper and a hard pencil are also needed." Russian calfskin is best for tooling and stamping.
3

Make the paper pattern

The purse has three parts: front, back and flap. Fold paper to the proportions you want, with the design for the front D on the same side of the paper as the flap C; the space F under the flap has no design. Fold F behind H, then C behind H and F, and turn the pattern over to see the purse. Cut a piece of leather 4 by 8 in, which leaves 1/4 in outside the pattern for pinning.

Materiały do tego kroku:

Skóra cielęcaSkóra cielęca1 sztuka

Potrzebne narzędzia:

Kalka technicznaKalka techniczna
OłówekOłówek
NożyczkiNożyczki
LinijkaLinijka
4

Damp the leather and transfer the design

Draw the whole design for the purse on tracing paper. Wet the leather on the wrong (unfinished) side with a soft sponge: pat it to moisten, not soak, it; too wet and the tool sticks and leaves an uneven background. Pin the design firmly on the leather, tack the leather down on its outer margin to the glass or board, and go over every line with a hard pencil, with firm, even pressure. Lift the paper and go over the lines with the narrow lining tool, with a strong, firm stroke. A line design can stop here.

Materiały do tego kroku:

Skóra cielęcaSkóra cielęca1 sztuka

Potrzebne narzędzia:

GąbkaGąbka
Kalka technicznaKalka techniczna
OłówekOłówek
Pinezki (pudełko 50 sztuk)Pinezki (pudełko 50 sztuk)
Tafla szklanaTafla szklana
Modelarka do skóryModelarka do skóry
5

Tool or stamp the background

Leave at least 1/8 in between the edge of the pattern and the design. To tool, press the background down with the broad end in even, long strokes; if it will not go down, the leather is too dry, so take it off and damp the back again. Keep the edges sharp between pressed and raised parts. To stamp instead, strike a small carpenter's nail set lightly with a wooden mallet in rows of circles; too hard a blow cuts the leather.

Potrzebne narzędzia:

Modelarka do skóryModelarka do skóry
Pobijak do gwoździPobijak do gwoździ
Pobijak drewnianyPobijak drewniany
GąbkaGąbka
6

Line and stitch

Fold the parts together, line with silk to match the leather, and stitch the front and back parts close to the edge. Stitch on a sewing machine with a long stitch, a large needle and silk as heavy as the needle takes; try it on a scrap first, and put tissue paper over the leather if the foot marks it. Without a machine, prick holes with an awl and sew with needle and silk, running or over-and-over; going over-and-over to the end and back gives an X stitch. She has the catch M put on by a shoemaker or trunk store; a snap fastener is used here.

Materiały do tego kroku:

Tkanina jedwabnaTkanina jedwabna1 sztuka
Nić jedwabnaNić jedwabna1 sztuka
Klej pszennyKlej pszenny1 sztuka
ZatrzaskZatrzask1 sztuka

Potrzebne narzędzia:

NożyczkiNożyczki
Maszyna do szyciaMaszyna do szycia
SzydłoSzydło
Dwie igły rymarskieDwie igły rymarskie
7

Troubleshooting

Tooled leather troubleshooting.

Flow

Loading...
8

History and honest limits

From Mary C. Scovel, "Arts-Crafts Leather Work", in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 432-441), Part I. She gives the piece size but no finished purse size; the shape comes from her pattern. The snap fastener, tools and metric figures are ours.

Materiały

5

Wymagane narzędzia

13

Według tego planu powstaje

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...