Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA

Screw Auger: a Steel Blade Twisted Red-Hot, with a Worm, Two Lips and an Eye for the Cross Handle (Holtzapffel, 1846)
How the common English screw auger was made, from Holtzapffel's Turning and Mechanical Manipulation: a parallel steel blade twisted red-hot, a worm at the point to pull it into the wood, two lips sharpened to cut, and the shaft end forged into an eye for a tightly driven cross handle.
Zaawansowany
A day at the forge
Instrukcje
1
1
Twist count
Twist count
Wczytywanie notatnika Jupyter…
2
2
Read Holtzapffel
Read Holtzapffel
"The ordinary screw auger ... is forged as a parallel blade of steel ... it is twisted red-hot."
3
3
Forge the blade
Forge the blade
Draw a steel bar out into a flat, parallel blade, leaving a round end for the shaft. Width, thickness and length are ours: make the blade as wide as the hole you want.
Materiały do tego kroku:
Pręt ze stali narzędziowej1 sztukaPotrzebne narzędzia:
Kuźnia kowalska
Kowadło
Młotek
Szczypce kowalskie
Fuller (żelazo do rowkowania)4
4
Twist it red-hot
Twist it red-hot
Heat the blade to red, grip one end in the vice and twist the other with a wrench into an even double spiral. Twist in short heats and keep the pitch even.
Potrzebne narzędzia:
Kuźnia kowalska
Imadło warsztatowe
Pokrętło do gwintowników
Szczypce kowalskie5
5
Form the worm and lips
Form the worm and lips
File the point into a worm (a small tapered screw, as on a gimlet) that pulls the auger into the work. Shape and sharpen the two corners, or lips, to cut at the very ends and a little up the sides.
Potrzebne narzędzia:
Imadło warsztatowe
Pilniki (pilnik ręczny)6
6
Forge the eye
Forge the eye
Forge the top of the shaft into a ring or eye.
Potrzebne narzędzia:
Kuźnia kowalska
Kowadło
Młotek
Szczypce kowalskie7
7
Harden and temper (ours)
Harden and temper (ours)
He gives no hardening. Ours: harden the cutting end and temper it as for other wood-cutting edge tools, then hone the lips.
Potrzebne narzędzia:
Kuźnia kowalska
Kadź hartownicza
Osełka8
8
Fit the cross handle
Fit the cross handle
Shape a hardwood bar and drive it tightly through the eye as a transverse handle.
Materiały do tego kroku:
Deska z drewna liściastego1 sztukaPotrzebne narzędzia:
Ośnik
Młotek9
9
Troubleshooting
Troubleshooting
Screw auger troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
From Charles Holtzapffel, **Turning and Mechanical Manipulation**, vol. II (1846), pp. 540, 543 and 545-546 (checked on the archive.org scan turningmechanica02holtuoft). He also describes the single-lip auger: a half-round bar coiled into an open spiral with the flat side outwards, the end shaped like a shell auger. He gives no sizes or heat treatment: those, the tools and the handle wood are ours.
Materiały
2- 1 sztukaZastępnik
- 1 sztukaZastępnik
Wymagane narzędzia
11- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
- Zastępnik
Według tego planu powstaje
Powiązane blueprinty
Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami
CC0 Domena publiczna
Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.
Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.



