Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Instant-Read Thermometer: Digital, with a Stainless Probe That Pivots on the Case (Cook, US 5,018,875, 1991)
Penny

Autor

Penny

3. listopad 2026DK
10
0
0
0
0

Instant-Read Thermometer: Digital, with a Stainless Probe That Pivots on the Case (Cook, US 5,018,875, 1991)

A pocket digital thermometer. A thin stainless steel probe with a thermistor in its tip pivots on a small, flat-sided case, so you can push the probe into food and turn the display to face you. A button cell runs a chip and a liquid crystal display, and a push button updates the reading at once. The angled case will not roll off a table. Result: a thin-probe digital thermometer for food and air. Source: T. A. Cook (PSG Industries), US 5,018,875 (1991). Unknown: the circuit, the range, the case size. Picture: the patent drawing.
Średniozaawansowany
Unknown

Instrukcje

1

Make the probe

Cut a type 304 stainless steel tube about 0.166 in (4.0 mm) across and 5 in (120 mm) long, and close one end. Set a thermistor inside the closed tip and run its two wires up the tube. Aluminium or titanium would also serve.

Materiały do tego kroku:

Rura ze stali nierdzewnejRura ze stali nierdzewnej1 probe
Zestaw termistorów NTCZestaw termistorów NTC1 thermistor
Drut miedzianyDrut miedziany1 interconnecting wires

Potrzebne narzędzia:

Piła do metaluPiła do metalu
LutownicaLutownica
2

Mould the pivot boss and case

Mould from ABS a cylindrical pivot boss with a recess for the probe's open end and a channel right through it for the wires. Mould the case in an upper and a lower half that snap together, wider at the display end and tapering to the probe end so it cannot roll, with two projecting supports at the probe end, each with a pivot hole. Not given: the sizes.

Materiały do tego kroku:

Granulat ABSGranulat ABS1 boss and case

Potrzebne narzędzia:

WtryskarkaWtryskarka
Nieznane wymiaryNieznane wymiary
3

Fit the electronics and assemble

In the case, fit an integrated circuit that turns the thermistor's resistance into a reading on a liquid crystal display at the wide end, with a push button beside it that updates the reading at once. Add a compartment for a 1.5 V button cell (Eveready E675, IEC R07) under a cover that locks with a quarter turn. Push the probe into the boss, lead the wires through the channel to the circuit, and clamp the boss ends in the pivot holes as the halves snap together; friction holds whatever angle you set. In use, push the probe in, turn the display to face you and press the button. Not given: the circuit (the patent points to US 4,536,851).

Materiały do tego kroku:

Płytka drukowanaPłytka drukowana1 sztuka
Układ scalonyUkład scalony1 sztuka
Segmentowy wyświetlacz LCDSegmentowy wyświetlacz LCD1 sztuka
PrzyciskPrzycisk1 sztuka
Bateria guzikowa 1,5 VBateria guzikowa 1,5 V1 sztuka
Drut lutowniczyDrut lutowniczy1 as needed

Potrzebne narzędzia:

LutownicaLutownica

Materiały

10

Wymagane narzędzia

4

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...